Panasonic 98 Large Format 4K Professional Display Operating Instructions - Page 54

English

54

[Subnet mask]:

(Subnet mask display and setting)

Enter a Subnet mask when DHCP server is not

used.

[Gateway]:

(Gateway address display and setting)

Enter a gateway address when DHCP server is not

used.

Note

●

IP address will not be displayed when [DHCP] is

set to [On].

Entering numbers

1.

Select the item and press <ENTER>.

2.

Select digits with

.

3.

Change numbers with numeric buttons (<0> -

<9>).

It is also possible to change with

.

4.

Press <ENTER>.

You can cancel the change by pressing

<RETURN>.

Select [Save] and press <ENTER>.

Save the current network Setup.

Note

●

To use a DHCP server, make sure the DHCP server

is started.

●

Contact your network administrator for details on [IP

address], [Subnet mask] and [Gateway].

●

Shipping condition

[DHCP]: Off

[IP address]: 192.168.0.8

[Subnet mask]: 255.255.255.0

[Gateway]: 192.168.0.1

[Port]

Set the port number used for command control.

Select [Port] and press <ENTER> to set the number.

●

The available setting range is 1024 - 65535.

●

Entering numbers (see page 54)

Note

●

When the PJLink protocol is used, the port setting is

not necessary.

[DUPLEX]

Set the transmission method of the LAN environment.

[Auto], [100 Half], [100 Full]

[Network ID]

Set the ID to identify this unit.

Press [Network ID] and press <ENTER> to set the

number.

●

The available setting range is 0 - 99.

●

Entering numbers (see page 54)

■

[Name change]

The name of the Display that is shown on the network

can be changed.

Select [Name change] with

and press

<ENTER>.

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

a

b

c

d

e

f

g

h

i

j

k

l

m

n

o

p

q

r

s

t

u

v

w

x

y

z

0

1

2

3

4

5

6

7

8

9

!

”

#

$

%

&

’

+

–

/

=

?

_

`

|

~

<

>

(

)

[

]

{

}

,

@

\

ˆ

.

;

:

Name0000

█

Name change

Ok

Cancel

All delete

Delete

Space

●

Up to 8 characters can be set for Display name.

●

Entering characters (see page 74)

■

[Network control]

Set when controlling with the unit’s DIGITAL LINK /

LAN terminal.

[On]:

Controls via LAN using the LAN terminal of the

Display or twisted pair cable transmitter or via

RS-232C using the SERIAL (RS-232C) terminal of

twisted pair cable transmitter. The power indicator

lights orange when the power is turned off with the

remote control (standby).

[Off]:

Invalidates control with DIGITAL LINK / LAN

terminal.

(In this case, the power consumption of Standby

condition (when the power is turned off with the

remote control) will be slightly reduced.)

Note

●

Even when [Off] is selected, when the power is

turned on, HDMI communication via twisted pair

cable transmitter becomes possible.

●

For the case of [On], see [DIGITAL LINK mode]

(see page 55)

●

When this is set to [On] and [DIGITAL LINK(RS-

232C)] is selected in [DIGITAL LINK mode], it is not

possible to control with the unit’s SERIAL terminal.

■

[AMX D.D.]

Set whether to allow the Display to be detected by

AMX Device Discovery.

[On]:

Enables detection by AMX Device Discovery.

[Off]:

Disables detection by AMX Device Discovery.

●

For more details, visit the following web site.

http://www.amx.com/

Panasonic 98 Large Format 4K Professional Display Operating Instructions - Page 54

Name change], Network control], AMX D.D.]

Page 54 highlights