Panasonic WVCU360C WVCU360C User Guide - Page 16

MODE Switch Setting for System Example 2, Controller Number Setting (PS• Data), CONTROLLER No.

Get Panasonic WVCU360C - SYSTEM CONTROLLER PDF manuals and user guides
UPC - 791871503454
View all Panasonic WVCU360C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

q MODE Switch Setting for System Example 2 The MODE switch needs to be set prior to operating a system connected as shown in Example 2. OFF ON 12 3 4 56 78 Bit 3 should be set to OFF. Bit 5 should be set to OFF when the controller is placed in an intermediate position, or set to ON when it is connected at the chain end. s Controller Number Setting (PS •Data) A 10-position rotary switches provided on the rear for specifying the unit number of the WV-CU360C controller in a PS •Data system. 1. Remove the DC plug from the rear of the controller. 2. Use a screw driver to rotate the switch so that the arrow comes to the number you wish. 901 78 23 456 CONTROLLER No. 3. Connect the DC plug to the controller. Controller No. Switch of WV-CU360C 0 1 2 3 4 5 6 7 8 9 Controller No. Reserved 1 2 3 4 5 6 7 8 Reserved Notes: • Set the switch to #1 when a single controller is used in the system. • Specify a unique number for each controller when connecting multiple controllers in the system. One controller within the multiple controller system must be assigned the number 1. • Positions #0 and #9 are reserved and cannot be used. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
16
●
MODE Switch Setting for System Example 2
The MODE switch needs to be set prior to operating a sys-
tem connected as shown in Example 2.
Bit 3 should be set to OFF.
Bit 5 should be set to OFF when the controller is placed
in an intermediate position, or set to ON when it is con-
nected at the chain end.
■
Controller Number Setting (PS
•
Data)
A 10-position rotary switches provided on the rear for spec-
ifying the unit number of the WV-CU360C controller in a
PS
•
Data system.
1.
Remove the DC plug from the rear of the controller.
2.
Use a screw driver to rotate the switch so that the arrow
comes to the number you wish.
3.
Connect the DC plug to the controller.
Notes:
• Set the switch to #1 when a single controller is used in
the system.
• Specify a unique number for each controller when con-
necting multiple controllers in the system.
One con-
troller within the multiple controller system must be
assigned the number 1.
•
Positions #0 and #9 are reserved and cannot be used.
0
9
8
7
6
5
4
3
2
1
CONTROLLER No.
Controller No. Switch of WV-CU360C
Controller No.
0
Reserved
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
Reserved
1
2
3
4
5
6
7
8
OFF
ON