Home » Panasonic Manuals » Electronics Accessories » Panasonic WVCU360C » Manual Viewer

Panasonic WVCU360C WVCU360C User Guide - Page 36

Camera Patrol Learning, Patrol Play/patrol Learn, Program/cam Setup/cam, Function, Sequence/patrol

Get Panasonic WVCU360C - SYSTEM CONTROLLER PDF manuals and user guides

UPC - 791871503454

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

7. Move the cursor to [SPECIAL] on the Setup menu, and press numeric buttons 4 and 6 simultaneously for 2 seconds or more to display the special menu. 8. Move the cursor to [CAMERA RESET]* on the Setup menu, and press buttons 4, 5 and 6 simultaneously to reset all the functions to the defaults. * The menu to reset the camera functions differs depending on the camera: [SPECIAL] for the WV-CS650, [SPECIAL 2] for the WVCS854, and [END] for fixed cameras etc. Notes: • If camera setup is started using the buttons on the camera, all future operations for setup must be performed using the buttons on the camera. If camera setup is started using the System Controller, all future operations for setup must be performed using the same controller. • For further information, refer to the Operating Instructions for the selected camera. Keys used for camera setup s Camera Patrol Learning There are two ways of setting up camera patrol learning. One is to use the camera setup menu and the other is to operate the camera. Follow the procedures below to set up while operating the combination camera. 1. Select the desired system unit, monitor and combination camera. 2. Press the PATROL PLAY/PATROL LEARN button while holding down the PROGRAM/CAM SETUP/CAM FUNCTION button. PROGRAM CAM SETUP CAM FUNCTION PATROL PLAY PATROL LEARN [LEARNING] appears on the monitor. 2 8 To move the cursor 4 6 To select a parameter CAM To execute the mode or enter a submenu SET MON To return to the previous menu ESC LEARNING 3. Operate the camera using the following controls so that it traces a routine course most frequently patrolled. The learning is programmed for 30 seconds for later patrol play. • Pan/Tilt (Joystick) • Iris (Open/Close) • Focus (Far/Near) • Zoom (Tele/Wide) • Preset Position Note: The memorized parameters may differ somewhat depending on the camera type. Refer to the manual included with the camera. 4. To stop the learning, press the SEQUENCE/PATROL STOP button while holding down the PROGRAM/CAM SETUP/CAM FUNCTION button. PROGRAM CAM SETUP CAM FUNCTION SEQUENCE PATROL STOP [LEARNING] disappears from the monitor. 36

Section	Page
WV-CU360C	1
ENGLISH VERSION	2
IMPORTANT SAFETY INSTRUCTIONS	3
CONTENTS	4
PREFACE	5
FEATURES	5
PRECAUTIONS	5
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS	6
Rear View and AC Adapter	6
INSTALLATIONS	7
Template Mounting	7
Rear Panel Switch Setting (Summary)	8
Panasonic Security Data (PS•Data) Systems	9
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS	10
Front View (Template for PS• Data)	10
INSTALLATIONS (PS•Data)	13
System Connections	13
Connection Example	13
DATA Port Connection (PS • Data)	14
DIP Switch Setting (PS• Data)	15
MODE Switch Setting for System Example 2	16
Controller Number Setting (PS• Data)	16
CONTROLLER SETUP PROCEDURES (PS•Data)	17
Prior to Setup	17
Buttons and Controls used for Setup	17
Setup Menus	18
Administrator Authorization	19
Baud Rate	19
Parity	19
Wait Time	19
Controller Unit-Group Address	19
System Unit-Group Address	19
Unit A button Assignment	20
Unit B button Assignment	20
User Password	20
Administrator Password	20
User Password Certification	20
Camera Cleaning	21
Unit Connection Test	21
OPERATING PROCEDURES (PS•Data)	22
Basic Operating Flow	22
Login/Logout	23
Log In	23
Log Out	23
System Unit Selection	24
Selecting with Unit Number	24
Selecting with UNIT A/UNIT B Button	24
Monitor Selection	25
Camera Selection	25
Camera Control	26
Pan/Tilt Control	26
Lens Control	26
Home/Preset Position	26
Combination Camera Shortcuts	27
Housing/AUX Control	28
Defroster	28
Wiper	28
Auxiliary 1/2	28
Data Multiplex Unit Control	28
Setting	28
Camera Selection	28
Video Multiplexer Control	29
Multiscreen Selection	29
Still Picture	29
Electronic Zoom	29
Viewing Playback	30
Sequence Control	30
Digital Disk Recorder Control	31
WJ-HD100 Shortcuts	31
WJ-HD500A Shortcuts	32
Alarm Operation	34
Alarm Reset	34
Alarm Suspension	34
Alarm Recall	34
REMOTE SETUP of UNITS & CAMERAS	35
System Unit Setup	35
Camera Setup	35
Camera Patrol Learning	36
Camera Preset Position	37
For WJ-FS616C Multiplexer System	38
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS	39
Front View (Template for WJ-FS616C)	39
INSTALLATIONS (For WJ-FS616/FS616C)	42
System Connections	42
Connection Example	42
DATA Port Connection (For Multiplexer)	43
DIP Switch Setting (For Multiplexer)	43
Unit Version	44
Controller Number Setting	44
Switch Setting Procedures	44
SETUP PROCEDURES (For WJ-FS616/FS616C)	45
Prior to Setup	45
Buttons and Controls used for Setup	45
Controller Setup	46
Administrator Authorization	46
Baud Rate	46
Parity	46
OPERATING PROCEDURES (For WJ-FS616/FS616C System)	48
Camera Selection	48
Camera Control	48
Pan/Tilt Control	48
AUX Control	48
Alarm Operation	49
Alarm Reset	49
Alarm Suspension	49
VTR (VCR) Control	49
Camera Setup	50
General Setup	50
Shortcut for Preset Position Setup	50
For WJ-SX350 Matrix Switcher System	51
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS	52
Front View (Template for WJ-SX350)	52
INSTALLATIONS (For WJ-SX350)	55
System Connections	55
Connection Example	55
DATA Port Connection (For WJ-SX350)	56
DIP Switch Setting (For WJ-SX350)	56
Controller Number Setting	57
Switch Setting Procedures	57
CONTROLLER SETUP PROCEDURES (For WJ-SX350)	58
Prior to Setup	58
Buttons and Controls used for Setup	58
Setup Procedures	59
Administrator Authorization	59
Baud Rate	59
Parity	59
OPERATING PROCEDURES (For WJ-SX350)	60
Login & Logout	60
Login	60
Logout	60
Lens Control (Auto Focus Operation)	60
Pan/Tilt Control (Camera Position Operation)	60
Pan/Tilt Control (Auto/Random Panning)	61
Camera Housing Control	61
Wiper control	61
Defroster Control	61
Auxiliary Control	61
System Status Display	62
For System 850 WJ-SX850 Matrix Switcher System	63
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS	64
Front View (Template for System 850 Matrix Switcher)	64
INSTALLATIONS (For System 850)	68
System Connections	68
Connection Example	68
DATA Port Connection	69
DIP Switch Setting	70
Controller Number Setting	70
Switch Setting Procedures	70
SETUP PROCEDURES (For System 850)	71
Prior to Setup	71
Buttons and Controls used for Setup	71
Setup Procedures	72
Administrator Authorization	72
Baud Rate	72
Parity	72
OPERATING PROCEDURES (For System 850)	73
Login & Logout	73
Login	73
Logout	73
Appendix	74
SPECIFICATIONS	75
STANDARD ACCESSORIES	75

Match case Limit results 1 per page

■

Camera Patrol Learning

There are two ways of setting up camera patrol learning.

One is to use the camera setup menu and the other is to

operate the camera.

Follow the procedures below to set up while operating the

combination camera.

1. Select the desired system unit, monitor and combina-

tion camera.

2. Press the

PATROL PLAY/PATROL LEARN

button

while holding down the

PROGRAM/CAM SETUP/CAM

FUNCTION

button.

[LEARNING] appears on the monitor.

Operate the camera using the following controls so that

it traces a routine course most frequently patrolled. The

learning is programmed for 30 seconds for later patrol

play.

•

Pan/Tilt (Joystick)

•

Iris (Open/Close)

•

Focus (Far/Near)

•

Zoom (Tele/Wide)

•

Preset Position

Note:

The memorized parameters may differ somewhat

depending on the camera type. Refer to the manual

included with the camera.

4. To stop the learning, press the

SEQUENCE/PATROL

STOP

button while holding down the

PROGRAM/CAM

SETUP/CAM FUNCTION

button.

[LEARNING] disappears from the monitor.

7. Move the cursor to [SPECIAL] on the Setup menu, and

press numeric buttons

and

simultaneously for 2

seconds or more to display the special menu.

8. Move the cursor to [CAMERA RESET]* on the Setup

menu, and press buttons

and

simultaneously to

reset all the functions to the defaults.

The menu to reset the camera functions differs depend-

ing on the camera:

[SPECIAL] for the WV-CS650, [SPECIAL 2] for the WV-

CS854, and [END] for fixed cameras etc.

Notes:

• If camera setup is started using the buttons on the

camera, all future operations for setup must be per-

formed using the buttons on the camera.

If camera setup is started using the System

Controller, all future operations for setup must be

performed using the same controller.

• For further information, refer to the Operating

Instructions for the selected camera.

Keys used for camera setup

LEARNING

To move the cursor

To select a parameter

To execute the mode or

enter a submenu

To return to the previous menu

CAM

SET

MON

ESC

CAM FUNCTION

CAM SETUP

PROGRAM

CAM FUNCTION

CAM SETUP

PROGRAM

PATROL PLAY

PATROL

LEARN

SEQUENCE

PATROL

STOP