Panasonic WVCU360C WVCU360C User Guide - Page 25

Monitor Selection, Camera Selection, MON/ESC, Notes, CAM/SET, SHIFT, EL-ZOOM, STILL

Get Panasonic WVCU360C - SYSTEM CONTROLLER PDF manuals and user guides
UPC - 791871503454
View all Panasonic WVCU360C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

s Monitor Selection A monitor is selected when multiple monitors are connected to a system unit (e.g., a Video Multiplexer) to control such functions as multiscreen display and electronic zoom. 1. Select the system unit connected to the monitor you wish to control. 2. Enter a monitor number using the numeric buttons. s Camera Selection One of the cameras connected to the system unit is selected. 1. Select a system unit connected to the camera whose picture you wish to view. 2. Enter a camera number using the numeric buttons. The entered camera number appears on the LED display. 3. Press the CAM/SET button. MON CAM ESC LOGOUT SET 3. Press the MON/ESC button. MON ESC The selected monitor number appears in the monitor section of the LED display. The selected camera number appears in the camera section of the LED display. The monitor is now ready for control from the system controller. Notes: • To confirm the selected monitor number, simply take procedure 3 when the unit address appears in the monitor section of the LED display. • Each time the MON/ESC button is pressed, the unit number and monitor number are displayed alternately on the LED. • The setting is invalid if the unit in which the monitor number has been set is not programmed. • In the above case, repeat the same procedure after confirming the monitor number. If you do not know the monitor number, consult the administrator. • When [--] appears in the monitor section of the LED display, the selected system unit is not compatible with the monitor selection. • For further information, refer to the Operating Instructions for the system unit concerned. MON CAM ESC LOGOUT SET Note: [--] appears in the camera section of the LED display when an alarm is activated, when the multiscreen is displayed, or when a sequence mode is running. The following functions are available after selecting a camera. • Pan/tilt • Focus • Zoom • Iris • Defroster ON/OFF (camera housing) • Wiper ON/OFF (camera housing) • Preset Position (Combination Camera) • Home position (Combination Camera) • Switching between color and B/W picture (Combination Camera) • Auto pan (Combination Camera) • Patrol Learn function (Combination Camera) • Camera functions (Combination Camera) The selected camera number can be incremented or decremented by one if the system unit is equipped with the camera switching feature. 1. Press the SHIFT button to turn the shift indicator on. 2. Press the EL-ZOOM/+ button to increment or the STILL/- button to decrement the camera number. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
25
■
Monitor Selection
A monitor is selected when multiple monitors are connected
to a system unit (e.g., a Video Multiplexer) to control such
functions as multiscreen display and electronic zoom.
1. Select the system unit connected to the monitor you
wish to control.
2.
Enter a monitor number using the numeric buttons.
3.
Press the
MON/ESC
button.
The selected monitor number appears in the monitor
section of the LED display.
The selected camera number appears in the camera
section of the LED display.
The monitor is now ready for control from the system
controller.
Notes:
• To confirm the selected monitor number, simply
take procedure 3 when the unit address appears in
the monitor section of the LED display.
•
Each time the MON/ESC button is pressed, the unit
number and monitor number are displayed alter-
nately on the LED.
• The setting is invalid if the unit in which the monitor
number has been set is not programmed.
•
In the above case, repeat the same procedure after
confirming the monitor number. If you do not know
the monitor number, consult the administrator.
•
When [--] appears in the monitor section of the LED
display, the selected system unit is not compatible
with the monitor selection.
• For further information, refer to the Operating Inst-
ructions for the system unit concerned.
MON
CAM
LOGOUT
ESC
SET
MON
ESC
■
Camera Selection
One of the cameras connected to the system unit is select-
ed.
1. Select a system unit connected to the camera whose
picture you wish to view.
2.
Enter a camera number using the numeric buttons.
The entered camera number appears on the LED dis-
play.
3.
Press the
CAM/SET
button.
Note:
[--] appears in the camera section of the LED dis-
play when an alarm is activated, when the multi-
screen is displayed, or when a sequence mode is
running.
The following functions are available after selecting a cam-
era.
• Pan/tilt
• Focus
• Zoom
• Iris
• Defroster ON/OFF (camera housing)
• Wiper ON/OFF (camera housing)
• Preset Position (Combination Camera)
• Home position (Combination Camera)
• Switching between color and B/W picture
(Combination Camera)
• Auto pan (Combination Camera)
• Patrol Learn function (Combination Camera)
• Camera functions (Combination Camera)
The selected camera number can be incremented or
decremented by one if the system unit is equipped with the
camera switching feature.
1.
Press the
SHIFT
button to turn the shift indicator on.
2. Press the
EL-ZOOM/+
button to increment or the
STILL/–
button to decrement the camera number.
MON
CAM
LOGOUT
ESC
SET