Panasonic WVCU360C WVCU360C User Guide - Page 72

Administrator Authorization, Baud Rate, Parity

Page 72 highlights

s Setup Procedures Set up the baud rate and parity check mode for the controller while observing the LED on the front panel. Menu Selection LED Display Setup Menus Reading Function Setup Initial Display CAM SET Parameter Selection (default*) LED prompts you to enter password No OK Move Joystick UP and down to select blinking Administrator Password Prompt Authorization Speed Baud Rate (bps) Enter a 5-digit password, press CAM (12345*) Press twice CAM SET (1) 2 400 (2) 4 800 (3) 9 600* (4) 19 200 L R DOWN UP L R Parity Parity Check SET MON ESC (1) None* (2) Even q Administrator Authorization 1. Press the CAMERA (ENTER) button while [SEtUP] is displayed. The prompt appears. 2. Enter a password using the numeric buttons, then press the CAMERA (ENTER) button. The default setting is [12345]. 3. If the password entered is valid, [SPEED] appears. If password entry failed, the menu returns to [SEtUP]. q Baud Rate In this menu, the communication speed (bps: bits per second) is selected. The communication speed should match that of the WJ-SX850. 1. Display [SPEED], and press the CAMERA (ENTER) button twice. 2. Select a parameter entering a bracket-enclosed number, e.g., (3), moving the joystick. The default setting is 9 600 bps. (1) 2 400: 2 400 bps (2) 4 800: 4 800 bps (3) 9 600: 9 600 bps (4) 19 200: 19 200 bps 74 Note: Selecting a slower rate (e.g., 2 400 bps) will delay the response time (e.g., the time until an activated alarm is reset). 3. Press the CAMERA (ENTER) button to validate the selection. 4. Press the CLEAR(ESC) button to return to the [SPEED] menu. q Parity In this menu, the parity check mode is selected. 1. Display [PrtY] and press the CAMERA (ENTER) button twice. 2. Select a parameter with the joystick. The default setting is None. n: None E: Even parity 3. Press the CAMERA (ENTER) button to validate the selection. 4. Press the CLEAR(ESC) button to return to the [SPEED] menu. Note: The baud rate and parity check mode of the WJSX850 and the controller must be the same, otherwise data communications will not function.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77

74
Setup Procedures
Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
Menu
Selection
Move Joystick
UP and down
to select
Setup Menus
Parameter Selection (default*)
LED Display
blinking
Setup
Administrator
Password
Prompt
Speed
Parity
Initial
Display
Authorization
Baud Rate
(bps)
Press
twice
Parity Check
CAM
SET
CAM
SET
MON
ESC
LED prompts you to enter pass-
word
Enter a 5-digit password,
press
(12345*)
(1) 2 400
(2) 4 800
(3) 9 600*
(4) 19 200
(1) None*
(2) Even
Reading
Function
OK
No
DOWN
L
R
UP
L
R
CAM
SET
Administrator Authorization
1. Press the
CAMERA (ENTER)
button while [SEtUP] is
displayed.
The [- - - - -] prompt appears.
2.
Enter a password using the numeric buttons, then press
the
CAMERA (ENTER)
button.
The default setting is [12345].
3. If the password entered is valid, [SPEED] appears.
If
password entry failed, the menu returns to [SEtUP].
Baud Rate
In this menu, the communication speed (bps: bits per sec-
ond) is selected.
The communication speed should match
that of the WJ-SX850.
1. Display [SPEED], and press the
CAMERA (ENTER)
button twice.
2. Select a parameter entering a bracket-enclosed num-
ber, e.g., (3), moving the joystick.
The default setting is 9 600 bps.
(1) 2 400:
2 400 bps
(2) 4 800:
4 800 bps
(3) 9 600:
9 600 bps
(4) 19 200:
19 200 bps
Note:
Selecting a slower rate (e.g., 2 400 bps) will
delay the response time (e.g., the time until an acti-
vated alarm is reset).
3. Press the
CAMERA (ENTER)
button to validate the
selection.
4.
Press the
CLEAR(ESC)
button to return to the [SPEED]
menu.
Parity
In this menu, the parity check mode is selected.
1.
Display [PrtY] and press the
CAMERA (ENTER)
button
twice.
2.
Select a parameter with the joystick.
The default setting is None.
n:
None
E:
Even parity
3. Press the
CAMERA (ENTER)
button to validate the
selection.
4.
Press the
CLEAR(ESC)
button to return to the [SPEED]
menu.
Note:
The baud rate and parity check mode of the WJ-
SX850 and the controller must be the same, otherwise
data communications will not function.