Sony BVME170A User Manual (Operating Instructions - BVM-E250A / BVM-E170A) - Page 118
Input, Output, General
View all Sony BVME170A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 118 highlights
Appendixes 4) The BVM-E170A individual chromaticity points. The widest color space setting of the signal reproduced by the BVM-E170A x y R 0.681 0.319 G 0.189 0.724 B 0.141 0.051 (Typical) 5) For displaying the color gamut of the wide color space mode S-GAMUT, which is available for the F23 or F35 Digital Cinematography Camera Warm-up time Approx. 30 minutes Input SDI BNC (×2) Input impedance: 75 ohms unbalanced Signal format See "Available Signal Systems" (page 122) and "Available Signal Formats" (page 124). Sampling frequency 3G-SDI: Y/Cb/Cr (4:2:2) 148.5MHz/74.25MHz/74.25MHz Y/Cb/Cr (4:4:4) 148.5MHz/148.5MHz/148.5MHz G/B/R (4:4:4) 148.5MHz/148.5MHz/148.5MHz HD-SDI: Y/Cb/Cr (4:2:2) 74.25MHz/37.125MHz/37.125MHz SD-SDI: Y/Cb/Cr (4:2:2) 13.5MHz/6.75MHz/6.75MHz Quantization 3G-SDI: 10 bit/sample, 12 bit/sample HD-SDI: 10 bit/sample SD-SDI: 10 bit/sample HDMI HDMI (×1) HDCP correspondence, Deep Color correspondence Signal format See "HDMI/DisplayPort" (page 130) of "Available Signal Formats". DisplayPort DisplayPort connector (×1) HDCP correspondence, 18/24/30bpp (bits per pixel) correspondence Signal format See "HDMI/DisplayPort" (page 130) of "Available Signal Formats". Option port Four (4) ports Signal format See "Available Signal Systems" (page 122) and "Available Signal Formats" (page 124). Parallel remote D-sub 9-pin (female) (×1) Serial remote (LAN) Ethernet (10BASE-T/100BASE-TX), RJ-45 (×1) Output SDI DC 5V OUT BNC (×1) (monitor output) Output signal amplitude: 800 mVp-p±10% Output impedance: 75 ohms unbalanced Transmission distance 3G-SDI: 70 m max.6) HD-SDI: 100 m max.6) SD-SDI: 200 m max.7) Note The signal from the monitor output connector does not satisfy the ON-LINE signal specifications. 6) When using the 5C-FB coaxial cable made by Fujikura Ltd. or equivalent 7) When using the 5C-2V coaxial cable made by Fujikura Ltd. or equivalent Circle 4-pin (female) (×1) General Power requirements 100 V to 240 V AC, 1.2 A to 0.7 A, 50/60 Hz 24 V to 28 V DC, 4.5 A to 3.9 A Power consumption Approx. 110 W (AC power supply)/ approx. 100 W (DC power supply) (maximum) Approx. 60 W (AC power supply)/ approx. 60 W (DC power supply) (average power consumption in the default status) Inrush current (1) Maximum possible inrush current at initial switch-on (Voltage changes caused by manual switching): 55 A peak, 15 A r.m.s. (240V AC) (2) Inrush current after a mains interruption of five seconds (Voltage changes caused at zero-crossing): 36 A peak, 7 A r.m.s. (240V AC) Operating temperature 0 °C to 35 °C (32 °F to 95 °F) Recommended: 20 °C to 30 °C (68 °F to 86 °F) Operating humidity 0% to 90% (no condensation) Storage/transport temperature -20 °C to +60 °C (-4 °F to +140 °F) Storage/transport humidity 0% to 90% 118 Specifications (BVM-E170A)