Sony BVME170A User Manual (Operating Instructions - BVM-E250A / BVM-E170A) - Page 23

Version of the Controller, Installing an Input Adaptor (BVM-E250A

Get Sony BVME170A PDF manuals and user guides View all Sony BVME170A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Chapter 2 Preparations Version of the Controller To use all the functions of the monitor, the controller (BKM-16R) with software version 1.7 or higher is required. Certain functions of the monitor cannot be controlled if the controller with a lower version is used. Installing an Input Adaptor (BVM-E250A) 1 Loosen two screws and remove the cover of an input option port on the side panel of the monitor. Cover of an input option port Make sure the MAIN POWER switch is turned off, and disconnect the AC power cord. Off 2 Insert the adaptor facing the board as shown below. Board 3 Push the adaptor in until it is firmly fit into the connector inside the monitor, then tighten the two screws to secure the adaptor. 23 Version of the Controller / Installing an Input Adaptor (BVM-E250A)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
23
Version of the Controller / Installing an Input Adaptor (BVM-E250A)
Chapter 2
Preparations
Version of the Controller
To use all the functions of the monitor, the controller
(BKM-16R) with software version 1.7 or higher is
required.
Certain functions of the monitor cannot be controlled if the
controller with a lower version is used.
Installing an Input
Adaptor (BVM-E250A)
1
Loosen two screws and remove the cover of an input
option port on the side panel of the monitor.
2
Insert the adaptor facing the board as shown below.
3
Push the adaptor in until it is firmly fit into the
connector inside the monitor, then tighten the two
screws to secure the adaptor.
Cover of an input
option port
Make sure the MAIN
POWER switch is turned
off, and disconnect the AC
power cord.
Off
Board