Toro 20330 Service Manual - Page 126

Adjusting the Personal Pace Cable, Personal Pace Generation 2/Easy Stride, Generation 2, Handle

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

HANDLES AND CONTROL CABLES Adjusting the Personal Pace Cable Ensure the transmission belt is disengaged, transmission tilted forward. Loosen the cable clamp on the handle. When you pull the cable down the personal place handle should raise to the stop. Hold the cable and secure the clamp (Fig. 236). This is the second generation of the personal pace/ easy stride handle assembly. It works the same as the original in the sense that the handle is telescoping. As the handle is depressed it tightens the self propelled belt and drives the transmission. Handle Removal To ease removal of the Personal Pace handle from a 22" Recycler, make a tool from a piece of metal strapping or banding material. You will need two pieces about 5" (12.7cm) long each. Bend them as shown in the photo and round the ends to remove burrs. This tool permits the handle to slide up and over the internal handle stops (Fig. 238). Fig 236 DSC-4829a Personal Pace Generation 2/Easy Stride Generation 2 Fig 238 MVC-712 1. Disconnect the control cables and the key switch (electric start models) from the upper handle and Personal Pace handle. Separate the upper and lower handle. Remove the brake bail by pressing the two ends together until they come out of the holes in the handle. Fig 237 20018_handle 7-6 WPM Drive Systems Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
7-6
WPM Drive Systems Manual
HANDLES AND CONTROL CABLES
Adjusting the Personal Pace Cable
Ensure the transmission belt is disengaged, transmission
tilted forward. Loosen the cable clamp on the handle.
When you pull the cable down the personal place handle
should raise to the stop. Hold the cable and secure the
clamp (Fig. 236).
Fig 236
DSC-4829a
Fig 237
20018_handle
Fig 238
MVC-712
To ease removal of the Personal Pace handle from a 22”
Recycler, make a tool from a piece of metal strapping
or banding material. You will need two pieces about 5”
(12.7cm) long each. Bend them as shown in the photo
and round the ends to remove burrs. This tool permits
the handle to slide up and over the internal handle stops
(Fig. 238).
This is the second generation of the personal pace/
easy stride handle assembly. It works the same as the
original in the sense that the handle is telescoping. As
the handle is depressed it tightens the self propelled belt
and drives the transmission.
Personal Pace Generation 2/Easy Stride
Generation 2
Handle Removal
1.
Disconnect the control cables and the key switch
(electric start models) from the upper handle and
Personal Pace handle. Separate the upper and
lower handle. Remove the brake bail by pressing the
two ends together until they come out of the holes in
the handle.