Toro 20330 Service Manual - Page 131

Cable Adjustment, Self-Propel Cable, Handle Disassembly, Lawn-Boy Blade, Clutch System BCS Models

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

HANDLES AND CONTROL CABLES Cable Adjustment The engine brake cable is not adjustable. If it fails to function it will need to be replaced. Self-Propel Cable To properly adjust the self propel cable, loosen the cable clamp, pull the cable downward to remove all the slack (Fig. 250) then push the cable jacket up 1/8" (3.17cm) (Fig. 251) and secure with the cable clamp. 1. Cable clamp Fig 251 2. Cable G002634 1. Cable Fig 250 Handle Disassembly, Lawn-Boy Blade Clutch System (BCS) Models G002635 1. Remove the upper wire bail. On the right hand side it slides over a pin. On some models this pin has a push nut on it (Fig. 252). It can be compressed so that either the bail slides off the pin or it draws the pin out of the handle. Either is acceptable. WPM Drive Systems Manual Fig 252 DSC-4871a 7-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
7-11
WPM Drive Systems Manual
HANDLES AND CONTROL CABLES
The engine brake cable is not adjustable. If it fails to
function it will need to be replaced.
Fig 251
G002634
Fig 250
G002635
To properly adjust the self propel cable, loosen the cable
clamp, pull the cable downward to remove all the slack
(Fig. 250) then push the cable jacket up 1/8” (3.17cm)
(Fig. 251) and secure with the cable clamp.
Cable Adjustment
Self-Propel Cable
Handle Disassembly, Lawn-Boy Blade
Clutch System (BCS) Models
1.
Remove the upper wire bail. On the right hand side
it slides over a pin. On some models this pin has a
push nut on it (Fig. 252). It can be compressed so
that either the bail slides off the pin or it draws the
pin out of the handle. Either is acceptable.
Fig 252
DSC-4871a
1. Cable
1. Cable clamp
2. Cable