Toro 20330 Service Manual - Page 61

C. Pulley half

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

SINGLE SPEED BEVEL GEAR TRANSMISSION 16. Push the transmission to the left, as shown, and rotate to clear the tunnel. Drop the left side down, then pull the assembly out to the left side (Fig. 104). Fig 102 MVC-211x1 15. Remove the nut, washer, 2 pulley halves, and spacer from the transmission input shaft. Remove 2 screws securing the belt guide to the transmission (Fig. 103). Fig 104 MVC-300 17. The last step is to slide the bearings and bearing retainers off the axle (Fig. 105). A F B C D E A. 2 screws on top of transmission B. Spacer C. Pulley half Fig 103 D. Pulley half E. Washer F. Nut PICT-1926 Fig 105 MVC-301 WPM Drive Systems Manual 3-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
3-23
WPM Drive Systems Manual
SINGLE SPEED BEVEL GEAR TRANSMISSION
Fig 103
PICT-1926
15. Remove the nut, washer, 2 pulley halves, and
spacer from the transmission input shaft. Remove 2
screws securing the belt guide to the transmission
(Fig. 103).
Fig 102
MVC-211x1
A. 2 screws on top
D. Pulley half
of transmission
E. Washer
B. Spacer
F.
Nut
C. Pulley half
A
B
C
D
E
F
16. Push the transmission to the left, as shown, and
rotate to clear the tunnel. Drop the left side down,
then pull the assembly out to the left side (Fig. 104).
Fig 104
MVC-300
17. The last step is to slide the bearings and bearing
retainers off the axle (Fig. 105).
Fig 105
MVC-301