Toro 20330 Service Manual - Page 72

Output Shaft Assembly

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

THREE SPEED TRANSMISSION Output Shaft Assembly 1. Slide the output bushing onto the output shaft, flanged side last. Assemble from the end of the shaft closest to the hole for the roll pin. 2. Slide the gear sleeve onto the output shaft, tabs last and secure with a new roll pin. 3. Apply a light coat of lithium-based grease on the output shaft under the output busing, on the gear sleeve, and on the three output shaft gears. Slide the three output shaft gears onto the gear sleeve, notched sides last. 4. Slide the nylon shift key sleeve onto the output shaft, large end first. Make sure that it engages the tabs on the gear sleeve (Fig. 123). 5. Coat the shift key sleeve with grease and prepare the shift keys, shift collar, and spring clip for assembly as shown in Figure 124. Fig 124 3428-0065 A 6. Slide the shift key assembly into the shift key sleeve until the shift collar bottoms out. 7. Complete the output shaft assembly by sliding a spacer washer and the other output bushing, flanged side first, onto the output shaft. Don't forget to coat these components with a light coat of grease (Fig. 125). A. Shift key sleeve Fig 123 492-4733 fig. 4-1 Fig 125 3428-0066 4-8 WPM Drive Systems Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
4-8
WPM Drive Systems Manual
THREE SPEED TRANSMISSION
Output Shaft Assembly
1.
Slide the output bushing onto the output shaft,
flanged side last. Assemble from the end of the shaft
closest to the hole for the roll pin.
2.
Slide the gear sleeve onto the output shaft, tabs last
and secure with a new roll pin.
3.
Apply a light coat of lithium-based grease on the
output shaft under the output busing, on the gear
sleeve, and on the three output shaft gears. Slide
the three output shaft gears onto the gear sleeve,
notched sides last.
4.
Slide the nylon shift key sleeve onto the output shaft,
large end first. Make sure that it engages the tabs on
the gear sleeve (Fig. 123).
Fig 123
492-4733 fig. 4-1
A. Shift key sleeve
Fig 125
3428-0066
6.
Slide the shift key assembly into the shift key sleeve
until the shift collar bottoms out.
7.
Complete the output shaft assembly by sliding a
spacer washer and the other output bushing, flanged
side first, onto the output shaft. Don’t forget to coat
these components with a light coat of grease (Fig.
125).
Fig 124
3428-0065
5.
Coat the shift key sleeve with grease and prepare
the shift keys, shift collar, and spring clip for
assembly as shown in Figure 124.
A