Toro 20330 Service Manual - Page 38

and Control Cables

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

SINGLE SPEED SPUR/BEVEL GEAR TRANSMISSION Prior to installation of oil impregnated bushings, it is wise to apply a light coating of engine oil to the running surface (Fig. 037). Add grease and install the cover. Insert the transmission back into the chassis. Refer to the section on the wheel pinion clutch for assembly instructions. Install self propel cable. Adjust as needed; see "Handles and Control Cables" Section 7. Fig 037 3428-0019 Finally, install the spacer and pulley on the input shaft. The internal gears will help hold the pinion while the nut is tightened (Fig. 038). Fig 038 3428-0022 2-6 WPM Drive Systems Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
2-6
WPM Drive Systems Manual
SINGLE SPEED SPUR/BEVEL GEAR TRANSMISSION
Prior to installation of oil impregnated bushings, it is
wise to apply a light coating of engine oil to the running
surface (Fig. 037). Add grease and install the cover.
Fig 037
3428-0019
Finally, install the spacer and pulley on the input shaft.
The internal gears will help hold the pinion while the nut
is tightened (Fig. 038).
Fig 038
3428-0022
Insert the transmission back into the chassis. Refer
to the section on the wheel pinion clutch for assembly
instructions.
Install self propel cable. Adjust as needed; see “Handles
and Control Cables” Section 7.