Toro 20330 Service Manual - Page 37

single spur gear to the axle Fig. 036. The other pin - replacement parts

Get Toro 20330 - Low Wheel Walk Power Mower PDF manuals and user guides
UPC - 021038203300
View all Toro 20330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

SINGLE SPEED SPUR/BEVEL GEAR TRANSMISSION Before removing the parts from the case, note the quantity and location of the thrust washers (Fig. 034). Clean the gears in solvent and inspect carefully. Any damaged gear must be replaced. Also replace the mate for the damaged gear. When gears run together, they develop a wear pattern that will result in premature failure if only one gear is replaced. The exception for this is if the transmission has VERY little running time before failure. The axle has two roll pins through it. One connects the single spur gear to the axle (Fig. 036). The other pin aligns the axle and transmission case. Fig 034 108-8140-1b Remove the axle and intermediate shaft with the gears. The bearing in the cover should be sealed on both sides. Inspect the bearing and its seals for damage (Fig. 035). Replace as necessary. The bearing is pressed into the cover. Make sure bearing is fully seated. Fig 036 3428-0016 Assembly Assemble with the correct number of thrust washers. Refer to the parts manual if there is any doubt at all. It is not possible to locate the shafts and bearings in the wrong location, due to differences in sizes. Fig 035 3428-0018 WPM Drive Systems Manual 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
2-5
WPM Drive Systems Manual
Fig 035
3428-0018
Remove the axle and intermediate shaft with the gears.
The bearing in the cover should be sealed on both sides.
Inspect the bearing and its seals for damage (Fig. 035).
Replace as necessary. The bearing is pressed into the
cover. Make sure bearing is fully seated.
Fig 034
108-8140-1b
Before removing the parts from the case, note the
quantity and location of the thrust washers (Fig. 034).
Clean the gears in solvent and inspect carefully. Any
damaged gear must be replaced. Also replace the mate
for the damaged gear. When gears run together, they
develop a wear pattern that will result in premature
failure if only one gear is replaced. The exception for this
is if the transmission has VERY little running time before
failure.
The axle has two roll pins through it. One connects the
single spur gear to the axle (Fig. 036). The other pin
aligns the axle and transmission case.
Fig 036
3428-0016
SINGLE SPEED SPUR/BEVEL GEAR TRANSMISSION
Assemble with the correct number of thrust washers.
Refer to the parts manual if there is any doubt at all. It
is not possible to locate the shafts and bearings in the
wrong location, due to differences in sizes.
Assembly