Toshiba 19CV100U User Manual - Page 32

Viewing the digital signal meter, Setting the Time Zone, Viewing the system status, Reset Factory

Get Toshiba 19CV100U PDF manuals and user guides View all Toshiba 19CV100U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 5: Setting up your TV Viewing the digital signal meter You can view the digital signal meter in the ANT/ CABLE digital TV input source only. To view the digital signal meter: 1 From the Setup menu, press or to select Installation and then press . 2 Press or to highlight Terrestrial, and press or to select Signal Meter and then press . 3 Press to select the antenna input and digital channel whose signal you want to check. Note: • The physical digital channel number listed in the Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations. • The signal strength does not change between virtual channels on the same physical channel. Setting the Time Zone The Time Zone setup will allow you to specify the correct time zone for your region. This feature will allow the TV status information to show the correct time zone information for your viewing area. To set the time zone: 1 From the Setup menu, press or to select Installation and then press . 2 Press or to highlight Terrestrial, and press or to select Time Zone and then press . 3 Press and then or to select the region. 4 Highlight Done, and then press . After the time zone has been set, you will be asked to set the current Daylight Saving Time status. To set the Daylight Saving Time Status: 1 Press or to select Yes or No, highlight Done, and then press . Viewing the system status 1 From the Setup menu, press or to select Installation and then press . 2 Press or to highlight System Status, and press or to select System Information and then press . 3 Press or to scroll through the menu bar to select Support Information and view the related information. Reset Factory Defaults 1 From the Setup menu, press or to select Installation and then press . 2 Press or to highlight System Status, and press or to select System Information and then press . 3 Press or to scroll through the menu bar to select Factory Defaults. 4 Enter your PIN code (or 0000 if no PIN code has been set). 5 Highlight Yes and then press . The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the reset process. To cancel the reset: Highlight No and then press . 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
32
Chapter 5: Setting up your TV
Viewing the digital signal meter
You can view the digital signal meter in the ANT/
CABLE digital TV input source only.
To view the digital signal meter:
Setting the Time Zone
The Time Zone setup will allow you to specify the
correct time zone for your region. This feature will
allow the TV status information to show the
correct time zone information for your viewing
area.
To set the time zone:
After the time zone has been set, you will be asked
to set the current Daylight Saving Time status.
To set the Daylight Saving Time Status:
Viewing the system status
Reset Factory Defaults
To cancel the reset:
Highlight
No
and then press
.
1
From the
Setup
menu, press
or
to
select
Installation
and then press
.
2
Press
or
to highlight
Terrestrial
, and
press
or
to select
Signal Meter
and
then press
.
3
Press
to select the antenna input
and digital channel whose signal you want to
check.
Note:
•
The physical digital channel number
listed in the Signal Meter screen may not
correspond to a virtual TV channel
number. Contact your local
broadcasters to obtain the RF channel
numbers for your local digital stations.
•
The signal strength does not change
between virtual channels on the same
physical channel.
1
From the
Setup
menu, press
or
to
select
Installation
and then press
.
2
Press
or
to highlight
Terrestrial
, and
press
or
to select
Time Zone
and then
press
.
3
Press
and then
or
to select the region.
4
Highlight
Done
, and then press
.
1
Press
or
to select
Yes
or
No
, highlight
Done
, and then press
.
1
From the
Setup
menu, press
or
to
select
Installation
and then press
.
2
Press
or
to highlight
System Status
,
and press
or
to select
System
Information
and then press
.
3
Press
or
to scroll through the menu bar to
select
Support Information
and view the
related information.
1
From the
Setup
menu, press
or
to
select
Installation
and then press
.
2
Press
or
to highlight
System Status
,
and press
or
to select
System
Information
and then press
.
3
Press
or
to scroll through the menu bar to
select
Factory Defaults
.
4
Enter your PIN code (or 0000 if no PIN code
has been set).
5
Highlight
Yes
and then press
. The TV will
turn off automatically after a few seconds.
After the TV turns off, unplug the TV power
cord and then plug it in again to complete the
reset process.