Toshiba Tecra R850 User Manual - Page 106

Removing a memory module, Power and Power-Up Modes, if required.

Get Toshiba Tecra R850 PDF manuals and user guides View all Toshiba Tecra R850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

R850/R840/R830 8. Seat the memory module cover in place and secure it with the screw(s). Take care to ensure that the memory module cover is firmly closed. Figure 3-16 Seating the memory module cover (R830) 2 1 1. Memory module cover 2. Screws 9. Install the battery pack - refer to Replacing the battery pack section in Chapter 5, Power and Power-Up Modes, if required. 10. Turn your computer over. 11. Turn the computer on and make sure the added memory is recognized - to confirmed it, Start -> Control Panel -> System and Security -> System icon. Removing a memory module To remove the memory module, follow the steps as detailed below: 1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel. 4. Turn the computer upside down and remove the battery pack. 5. Loosen the screw(s) securing the memory module cover in place - please note that the screws are attached to the cover in order to prevent them from being lost. 6. Slide your fingernail or a thin object under the cover and lift it off. 7. Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle. User's Manual 3-41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
8.
Seat the memory module cover in place and secure it with the
screw(s).
Take care to ensure that the memory module cover is firmly closed.
Figure 3-16 Seating the memory module cover (R830)
1
2
1. Memory module cover
2. Screws
9.
Install the battery pack - refer to
Replacing the battery pack
section in
Chapter 5, Power and Power-Up Modes, if required.
10.
Turn your computer over.
11.
Turn the computer on and make sure the added memory is recognized
- to confirmed it,
Start -> Control Panel -> System and Security ->
System
icon.
Removing a memory module
To remove the memory module, follow the steps as detailed below:
1.
Shut down the computer - make sure the
Power
indicator is off (refer
to the
Turning off the power
section in Chapter 1, Getting Started if
required).
2.
Remove the AC adaptor and all cables and peripherals connected to
the computer.
3.
Close the display panel.
4.
Turn the computer upside down and remove the battery pack.
5.
Loosen the screw(s) securing the memory module cover in place -
please note that the screws are attached to the cover in order to
prevent them from being lost.
6.
Slide your fingernail or a thin object under the cover and lift it off.
7.
Push the latches away from the module in order to release it - a spring
will force one end of the module up at an angle.
R850/R840/R830
User's Manual
3-41