Xerox 8560MFP Advanced Features Guide - Page 67

Changing the Power Saver Timeout, System, Up Arrow, Down Arrow, Address, Properties, General, Warmup

Page 67 highlights

System Settings Changing the Power Saver Timeout To save energy, the system enters a Power Saver, low-energy consumption mode after a predefined period of time since its last activity. In this mode, most electrical systems are shut down. When a job is sent to the system, the system enters Warmup mode. You can also warm up the system by pressing the OK button on the control panel. If you find that the system is going into Power Saver mode too often and you do not want to wait while the system warms up, increase the length of time before the system goes into Power Saver mode. To change the Power Saver Timeout value, use one of the following options: ■ The system's control panel ■ CentreWare IS Using the Control Panel To change the Power Saver Timeout value on the control panel: 1. Press the System button. 2. Select General Setup, and then press the OK button. 3. Select System Controls, and then press the OK button. 4. Select Power Saver, and then press the OK button. 5. Press the Up Arrow or Down Arrow button to scroll to a selected Power Saver Timeout value. Select a larger value if you want to extend the length of time before the system goes into Power Saver mode. 6. Press the OK button. Using CentreWare IS To change the Power Saver Timeout value using CentreWare IS: 1. Launch your web browser. 2. Enter your system's IP address in the browser's Address field (http://xxx.xxx.xxx.xxx). 3. Click Properties. 4. Select the General folder on the left sidebar, and then click Warmup. 5. Select a value from the Power Saver Timeout drop-down list. 6. Click the Save Changes button at the bottom of the page. Phaser® 8510/8560MFP Multifunction Product 4-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100

System Settings
Phaser® 8510/8560MFP Multifunction Product
4-6
Changing the Power Saver Timeout
To save energy, the system enters a Power Saver, low-energy consumption mode after a pre-
defined period of time since its last activity. In this mode, most electrical systems are shut
down. When a job is sent to the system, the system enters Warmup mode. You can also warm
up the system by pressing the
OK
button on the control panel.
If you find that the system is going into Power Saver mode too often and you do not want to
wait while the system warms up, increase the length of time before the system goes into Power
Saver mode.
To change the Power Saver Timeout value, use one of the following options:
The system’s control panel
CentreWare IS
Using the Control Panel
To change the Power Saver Timeout value on the control panel:
1.
Press the
System
button.
2.
Select
General Setup
, and then press the
OK
button.
3.
Select
System Controls
, and then press the
OK
button.
4.
Select
Power Saver
, and then press the
OK
button.
5.
Press the
Up Arrow
or
Down Arrow
button to scroll to a selected Power Saver Timeout
value. Select a larger value if you want to extend the length of time before the system goes
into Power Saver mode.
6.
Press the
OK
button.
Using CentreWare IS
To change the Power Saver Timeout value using CentreWare IS:
1.
Launch your web browser.
2.
Enter your system’s IP address in the browser’s
Address
3.
Click
Properties
.
4.
Select the
General
folder on the left sidebar, and then click
Warmup
.
5.
Select a value from the
Power Saver Timeout
drop-down list.
6.
Click the
Save Changes
button at the bottom of the page.