Alpine 1004 Owners Manual - Page 36

Setting the XM Auxiliary Data Field, Subwoofer Control On and Off, Adjusting Source Signal Levels

Get Alpine 1004 - CVA - LCD Monitor PDF manuals and user guides View all Alpine 1004 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Other Useful Features MUTE/SETUP Setting the XM Auxiliary Data Field (ADF) gf Preset 4 Preset 5 Adjusting Source Signal Levels If the difference in volume level betweenFM radio and other sources is too great, adjust the FM signal level as follows. After carrying out steps 1 to 3 of "To display the SETUP screen" (page 29), perform the operation shown below. 1 When the monitor is open, press and hold MUTE/SETUP for at least 2 seconds. The SETUP screen appears. 2 Press preset 4 to select the RADIO setting mode. Press preset 4 again to select FM LEVEL. 3 Press g or f to select the FM signal level HIGH or LOW to make the signal levels between the FM band and other sources closer. For any other settings, press preset 4 or another preset button. 4 After setting is completed, press MUTE/SETUP to return to normal mode. 34-EN You can set the Auxiliary Data Field (ADF) display of the received channel. After carrying out steps 1 to 3 of "To display the SETUP screen" (page 29), perform the operation shown below. 1 When the monitor is open, press and hold MUTE/SETUP for at least 2 seconds. The SETUP screen appears. 2 Press preset 4 to activate the RADIO setting mode. Press preset 4 again to select XM ADF. 3 Press g or f to select ON or OFF. Select ON to display Auxiliary Data Field (ADF) in the XM mode (refer to "Changing the Display" on page 13). For any other settings, press preset 4 or another preset button. 4 After setting is completed, Press MUTE/SETUP to return to normal mode. Subwoofer Control On and Off After carrying out steps 1 to 3 of "To display the SETUP screen" (page 29), perform the operation shown below. 1 When the monitor is open, press and hold MUTE/SETUP for at least 2 seconds. 2 Press preset 5 to set to the SYSTEM setting mode. Press preset 5 again to select the SUBWOOFER mode. 3 Press g or f to select Subwoofer ON or OFF. For any other settings, press preset 5 or another preset button. 4 After setting is completed, press MUTE/SETUP to return to normal mode. NOTES • Initial mode is "SUBWOOFER ON." • Set to "SUBWOOFER OFF" unless the subwoofer is used. • When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader (page 8).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
34
-EN
Other Useful Features
Setting the XM Auxiliary Data Field
(ADF)
You can set the Auxiliary Data Field (ADF) display
of the received channel.
After carrying out steps 1 to 3 of
“
To display the
SETUP screen
”
(page 29), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP
for at least 2 seconds. The
SETUP screen appears.
2
Press
preset 4
to activate the RADIO setting
mode. Press
preset 4
again to select XM ADF.
3
Press
g
or
f
to select ON or OFF.
Select ON to display Auxiliary Data Field (ADF)
in the XM mode (refer to
“
Changing the Display
”
on page 13).
For any other settings, press
preset 4
or another
preset button.
4
After setting is completed, Press
MUTE/SETUP
to return to normal mode.
Subwoofer Control On and Off
After carrying out steps 1 to 3 of "To display the
SETUP screen" (page 29), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP
for at least 2 seconds.
2
Press
preset 5
to set to the SYSTEM setting
mode. Press
preset 5
again to select the
SUBWOOFER mode.
3
Press
g
or
f
to select Subwoofer ON or
OFF.
For any other settings, press
preset 5
or another
preset button.
4
After setting is completed, press
MUTE/SETUP
to return to normal mode.
NOTES
•
Initial mode is "SUBWOOFER ON."
•
Set to "SUBWOOFER OFF" unless the subwoofer is
used.
•
When the subwoofer is turned on, the subwoofer
output level can be adjusted. For more details, refer to
the Adjusting Volume/Balance/Fader (page 8).
Adjusting Source Signal Levels
If the difference in volume level betweenFM radio
and other sources is too great, adjust the FM
signal level as follows.
After carrying out steps 1 to 3 of
“
To display the
SETUP screen
”
(page 29), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP
for at least 2 seconds. The
SETUP screen appears.
2
Press
preset 4
to select the RADIO setting
mode. Press
preset 4
again to select FM
LEVEL.
3
Press
g
or
f
to select the FM signal level
HIGH or LOW to make the signal levels between
the FM band and other sources closer.
For any other settings, press
preset 4
or another
preset button.
4
After setting is completed, press
MUTE/SETUP
to return to normal mode.
MUTE/SETUP
g
f
Preset 4
Preset 5