Apple MC408LL Apple Technician Guide - Page 94
Top hard drive ambient thermal sensor flex cable 076-1370, Orient the round end of the tape up
 |
UPC - 885909370924
View all Apple MC408LL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 94 highlights
Top hard drive ambient thermal sensor (flex cable) (076-1370): (This sensor is also replaceable by replacing the flex cable, which comes with the sensor installed.) 1. Remove the adhesive cover and attach the sensor pad to the flex cable where shown below. 2. Verify the flex cable is installed on the hard drive. 3. Cut approximately a 1.5 cm length of the supplied black Kapton tape. 4. Orient the round end of the tape up, center the tape over the sensor and press to secure the tape over the sensor and to the flex cable, then wrap the ends of the tape over the top and bottom of the hard drive, as shown. 2010-08-03 Mac mini (Mid 2010) Take Apart - General Information 94
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89 -
90 -
91 -
92 -
93 -
94 -
95 -
96 -
97 -
98 -
99 -
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
 |
 |
Mac mini (Mid 2010) Take Apart — General Information
94
2010-08-03
Top hard drive ambient thermal sensor (flex cable) (076-1370):
(This sensor is also replaceable by replacing the flex cable, which comes with the sensor installed.)
1.
Remove the adhesive cover and attach the sensor pad to the flex cable where shown below.
2.
Verify the flex cable is installed on the hard drive.
3.
Cut approximately a 1.5 cm length of the supplied black Kapton tape.
4.
Orient the round end of the tape up, center the tape over the sensor and press to secure the
tape over the sensor and to the flex cable, then wrap the ends of the tape over the top and
bottom of the hard drive, as shown.