Brother International BES-116 Instruction Manual - English - Page 26

Replacement of Bobbin, Put a new bobbin in the bobbin case.

Get Brother International BES-116 PDF manuals and user guides View all Brother International BES-116 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Chapter 1 Preparation of Embroidery Machine 4-2 Replacement of Bobbin Note) Remove dust, lint and oil from the bobbin case before replacement. Removing bobbin case 1. Open the rotary hook cover q. w 2. Hold the knob w and take out the bobbin case. 3. Close the knob and take out the bobbin e. q e Replacing bobbin r t t Pull out by about 50 mm 24 1. Put a new bobbin in the bobbin case. Check the winding direction. (refer the figure) If the bobbin is inserted in the reverse direction, the lower thread may slip too much, resultingin a problem in embroidering. Check that the bobbin is pushed out of the bobbin case by about 0.5 mm. If not, the slip prevention spring of the bobbin case does not work. Adjust the height of the spring or replace it with a new one. Bobbin 0.5mm 2. Slide the thread under the tension spring t through the notch r. 3. Pull out the thread from the hole of the tension spring t. 4. Pull out the thread by about 50 mm. BES-116AC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Chapter 1
Preparation of Embroidery Machine
BES-116AC
24
0.5mm
4-2 Replacement of Bobbin
Note)
Remove dust, lint and oil from the bobbin case before replacement.
Removing bobbin case
1.
Open the rotary hook cover
q
.
2.
Hold the knob
w
and take out the bobbin
case.
3.
Close the knob and take out the bobbin
e
.
Replacing bobbin
1.
Put a new bobbin in the bobbin case.
Check the winding direction. (refer the figure)
If the bobbin is inserted in the reverse direction, the lower
thread may slip too much, resultingin a problem in em-
broidering.
Check that the bobbin is pushed out of the bobbin case
by about 0.5 mm.
If not, the slip prevention spring of the
bobbin case does not work.
Adjust the height of the
spring or replace it with a new one.
2.
Slide the thread under the tension spring
t
through the notch
r
.
t
Pull out by about
50 mm
Bobbin
3.
Pull out the thread from the hole of the
tension spring
t
.
4.
Pull out the thread by about 50 mm.
w
q
e
r
t