Brother International BES-116 Instruction Manual - English - Page 29

The X and Y, carriages move automatically so as to bring

Get Brother International BES-116 PDF manuals and user guides View all Brother International BES-116 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 1 Preparation of Embroidery Machine When the machine is turned on: If the machine is not ready to operate because the needle bars in the drive position are out of the normal position, the message "Needle stop position error" appears. Follow the steps below if this occurs. 1. Set "100° ( )" on the pulley to "STOP POSITION." 2. Press . STOP Note) Check if the needle bars are lowered. If so, return them to the normal stop position. (Refer to "Normal needle stop position" on page 27.) 3. The message "Moving frame" appears and a buzzer sounds four times. The X and Y carriages move automatically so as to bring the hoop center to the home position or to the position where it was located at the end of the previous operation. 4. The main menu appears. Normal needle stop position w q q w Viewing the inside through the clearance, needle bar is in the jump position at the top (as shown in the figure) and needle bar vertical piece q lowers to keep it from contact with needle bar clamp w. (The thread take-up lever is aligned with the index mark.) Note) When the power switch has been turned on or when restarting embroidering while the machine is stopped or suspended, be sure to return the needles to the normal stop position. • Align thread take-up to the normal position. • If the needle bar in the embroidering position is lowered with needle bar vertical piece q, separate them in the following manner. For safety, insert a tool such as a screwdriver into the clearance at the front left side of the needle bar case and turn the needle bar vertical piece w by pushing its end. When the needle bar and the needle bar vertical piece are separated, the needle bar is raised to the top by the spring. BES-116AC 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Chapter 1
Preparation of Embroidery Machine
BES-116AC
27
When the machine is turned on:
If the machine is not ready to operate because the needle bars in the drive position are out of
the normal position, the message "Needle stop position error" appears.
Follow the steps
below if this occurs.
1.
Set "100
°
(
)" on the pulley to "STOP
POSITION."
2.
Press
STOP
.
Note)
Check if the needle bars are lowered.
If so,
return them to the normal stop position. (Re-
fer to "Normal needle stop position" on page
27.)
3.
The message "Moving frame" appears and
a buzzer sounds four times.
The X and Y
carriages move automatically so as to bring
the hoop center to the home position or to
the position where it was located at the end
of the previous operation.
4.
The main menu appears.
Normal needle stop position
w
q
w
q
Viewing the inside through the clearance,
needle bar is in the jump position at the top
(as shown in the figure) and needle bar
vertical piece
q
lowers to keep it from
contact with needle bar clamp
w
.
(The
thread take-up lever is aligned with the
index mark.)
Note)
When the power switch has been turned on
or when restarting embroidering while the
machine is stopped or suspended, be sure to
return the needles to the normal stop posi-
tion.
•
Align thread take-up to the normal position.
•
If the needle bar in the embroidering posi-
tion is lowered with needle bar vertical
piece
q
, separate them in the following
manner.
For safety, insert a tool such as a
screwdriver into the clearance at the front
left side of the needle bar case and turn the
needle bar vertical piece
w
by pushing its
end.
When the needle bar and the needle
bar vertical piece are separated, the needle
bar is raised to the top by the spring.