D-Link DSR-1000AC Emulator

D-Link DSR-1000AC Manual

D-Link DSR-1000AC manual content summary:

  • D-Link DSR-1000AC | Emulator - Page 1
    CLI Reference Guide Unified Services Router D-Link Corporation Copyright © 2015. http://www.dlink.com
  • D-Link DSR-1000AC | Emulator - Page 2
    Guide DSR-500AC/1000AC Unified Services Router Version 1.00 Copyright © 2015 Copyright Notice This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual CIRCUMSTANCES SHALL D-LINK OR ITS
  • D-Link DSR-1000AC | Emulator - Page 3
    ...11 2.3 Movement Keys...11 2.4 Deletion Keys ...11 2.5 Escape Sequences 12 Chapter 3. Command Hierarchy in CLI 13 3.1 CLI Commands ...13 3.2 Router Configuration 13 Chapter 4. Global commands used in CLI 14 Chapter 5. Show commands used in CLI 15 Chapter 6. Configuration commands under branch
  • D-Link DSR-1000AC | Emulator - Page 4
    6.25 vpn sslvpn portal-layouts edit
  • D-Link DSR-1000AC | Emulator - Page 5
    Chapter 8. Configuration commands under branch SYSTEM 87 8.1 System NT-Domain-Settings 87 8.2 system Active-Directory-Settings 88 8.3 system LDAP_Settings 89 8.4 system POP3_Settings POP3_Server_Configuration 90 8.5 system POP3_Settings POP3_Trusted_CA 91 8.6 system logging ipv4 configure 91
  • D-Link DSR-1000AC | Emulator - Page 6
    9.2 util system_check dns_lookup
  • D-Link DSR-1000AC | Emulator - Page 7
    11.29 net ipv6_tunnel isatap delete
  • D-Link DSR-1000AC | Emulator - Page 8
    11.73 net tahi RA-Start...182 11.74 net ipv6_tunnel teredo configure 183 11.75 net upnp configure 184 11.76 net port-vlan lan_edit
  • D-Link DSR-1000AC | Emulator - Page 9
    12.31 security firewall smtpAlg approvedMailId edit
  • D-Link DSR-1000AC | Emulator - Page 10
    (CLI) for managing D-Link's DSR-500AC/1000AC router. The CLI user requires advanced knowledge about the configuration of the system, and it should be used only by those users who are familiar with CLI-based configuration. Note that the following features in the DSR Unified Services Router cannot be
  • D-Link DSR-1000AC | Emulator - Page 11
    Chapter 2. Basic commands available on the CLI 2.1 Context Sensitive Help [?] - Displays context sensitive help. This is either a list of possible command completions with summaries, or the full syntax of the current command. A subsequent repeat of this key, when a command has been resolved, will
  • D-Link DSR-1000AC | Emulator - Page 12
    2.5 Escape Sequences • !! - Substitutes the last command line. • !N - Substitutes the Nth command line (absolute as per 'history' command). • !-N - Substitutes the command line entered N lines before (relative). 12
  • D-Link DSR-1000AC | Emulator - Page 13
    Commands The CLI commands are divided into 4 categories: • Global commands • Show commands • Utility commands • Configuration commands 3.2 Router Configuration The router configuration is divided into 5 branches: • Net: Network Settings • Security: Security Settings • System: Admin Settings • Dot11
  • D-Link DSR-1000AC | Emulator - Page 14
    Chapter 4. Global commands used in CLI The global commands that are used in CLI are given below: • .exit: Exit this session • .help: Displays an overview of the CLI syntax • .top: Returns to the default mode • .reboot: Reboots the system. • .history: Displays the current session's command line
  • D-Link DSR-1000AC | Emulator - Page 15
    Chapter 5. Show commands used in CLI The show commands for all the above mentioned branches are outlined in this section. The command show activeDirectory-serverCheck? at the CLI prompt would give the description of all the show commands in the branch activeDirectory-serverCheck, which is as
  • D-Link DSR-1000AC | Emulator - Page 16
    18 show vpn pptp Shows pptp server details. 19 show vpn pptp server Shows pptp server details. 20 show vpn pptp server setup Displays pptp server setup. 21 show vpn pptp server connections Displays pptp server stats. 22 show vpn sslvpn Shows sslvpn settings. 23 show vpn sslvpn connections
  • D-Link DSR-1000AC | Emulator - Page 17
    be common to multiple APs, the SSID is not unique to an AP. In order for computers or devices to communicate via this wireless network serviced by this AP, all devices must select the same SSID from the list of wireless networks in the area.Broadcast: The field indicates whether SSID
  • D-Link DSR-1000AC | Emulator - Page 18
    will use when a frame transmission fails. It is used for both long and short frames, of size less than or equal to the RTS threshold. Supported Rate: The rate or rates (in Mbps) which the AP will advertise in the beacon frames. Displays Profile configuration. If no profile name is specified
  • D-Link DSR-1000AC | Emulator - Page 19
    Displays access point and radio statistics. This table shows a cumulative total of relevant wireless statistics for the APs and radios; the counter is reset when the device is rebooted. Radio Statistics: This table displays transmit/receive data for each radio. It has the following fields: Pkt(Tx/
  • D-Link DSR-1000AC | Emulator - Page 20
    APs that are configured for a particular radio. AP Name: This is the name of the AP. BSSID: The BSSID of the AP SSID: The SSID serviced by AP Profile: This field has a brief description of the security, encryption and authentication combination assigned to the AP. The command show POP3-Settings? at
  • D-Link DSR-1000AC | Emulator - Page 21
    event viewer can be defined in the Log Configuration commands Displays Page Wise, captured log messages of 12 show system log page the router activities from Event Log. The logs displayed on this event viewer can be defined in the Log Configuration commands 13 show system remote_management
  • D-Link DSR-1000AC | Emulator - Page 22
    Displays Access Control browsers Policies 35 show system group access_control_ip Displays Access Control ips Policies 36 show system firmwareVersion Displays the firmware Version. The command show ntDomain-serverCheck? at the CLI prompt would give the description of all the show commands in
  • D-Link DSR-1000AC | Emulator - Page 23
    waits for a response from the RADIUS server Retries: The number of tries the router will make to the RADIUS server before giving up. Secret: RADIUS server secret. Available VLANs 8 show net bandwidth traffic_selector services Displays a list of available services 9 show net ddns . 10 show net
  • D-Link DSR-1000AC | Emulator - Page 24
    19 show net dmz dhcp reserved_ip . 20 show net dmz dhcp reserved_ip setup Displays a list of DMZ DHCP Reserved Addresses. 21 show net dmz dhcp leased_clients . 22 show net dmz dhcp leased_clients list Shows a list of Available DMZ DHCP Leased Clients. 23 show net ethernet Displays
  • D-Link DSR-1000AC | Emulator - Page 25
    51 show net wan wan2 ipv4 status Displays ipv4 wan2 Information. 52 show net wan wan2 ipv4 setup Displays wan2 Setup Information. 53 show net wan wan3 Displays the wan3 configuration 54 show net wan wan3 threeG Shows ThreeG information. 55 show net wan wan3 threeG setup Displays ThreeG
  • D-Link DSR-1000AC | Emulator - Page 26
    81 show net routing static ipv4 setup Shows all the configured IPV4 routes. 82 show net routing static interface_list Shows all the interfaces on which static route can be configured 83 show net routing static ipv6 Displays IPv6 Static Routes Info 84 show net routing static ipv6 setup Shows
  • D-Link DSR-1000AC | Emulator - Page 27
    8 show security firewall custom_service setup Displays a list of available Custom Service configuration 9 show security firewall Displays Firewall Rules 10 show security firewall ipv4 Displays IPv4 Firewall Rules 11 show security firewall ipv4 setup Displays IPv4 Firewall
  • D-Link DSR-1000AC | Emulator - Page 28
    33 show security firewall vpn_passthrough . 34 show security firewall vpn_passthrough setup Displays VPN passthrough Configuration 35 show security webAccess . Displays security webAccess configuration and 36 show security webAccess setup rules Displays a list of Allowed IpAdrr/Network Web
  • D-Link DSR-1000AC | Emulator - Page 29
    17 vpn openvpn local_network Opens vpn commands. local networks configuration 18 vpn openvpn local_network add Adds a new local network. 19 vpn openvpn local_network edit Local network edit mode. 20 vpn openvpn local_network delete Openvpn local network delete mode.
  • D-Link DSR-1000AC | Emulator - Page 30
    41 vpn sslvpn portforwarding appconfig Sslvpn portforwarding application configuration commands. 42 vpn sslvpn portforwarding appconfig add Adds an application configuration rule. 43 vpn sslvpn portforwarding appconfig delete Deletes an application configuration rule. 44 vpn
  • D-Link DSR-1000AC | Emulator - Page 31
    68 vpn ipsec policy delete 69 vpn ipsec policy connect 70 vpn ipsec policy drop Deletes a vpn policy. Connects a vpn tunnel. Drops a vpn tunnel. The command dot11? at the CLI prompt would give the description of all the configuration commands in the branch dot11, which is
  • D-Link DSR-1000AC | Emulator - Page 32
    21 dot11 radio configure 802.11 radio configuration mode. 22 dot11 radio advanced Advanced radio configure 23 dot11 radio advanced configure 802.11 AP advanced configuration mode. 24 dot11 accesspoint wps Advanced AP configure 25 dot11 accesspoint wps configure 802.
  • D-Link DSR-1000AC | Emulator - Page 33
    https. 20 system remote_management https configure Configures https. remote management support for 21 system remote_management telnet configure Configures telnet. remote management support for 22 system sessionSettings Session Settings Configuration. 23 system sessionSettings admin
  • D-Link DSR-1000AC | Emulator - Page 34
    45 system admin_setting configure System configuration mode. 46 system time System time configuration mode 47 system time configure System time configuration mode 48 system traffic_meter Traffic meter Configuration setup. 49 system traffic_meter configure Traffic meter configuration mode.
  • D-Link DSR-1000AC | Emulator - Page 35
    other Server on the Internet 5 util system_check traceroute Displays all the routers present between the destination IP address and this router 6 util system_check display_IPV4_routingtable Displays IPV4 Routing Table 7 util system_check display_IPV6_routingtable Displays IPV6
  • D-Link DSR-1000AC | Emulator - Page 36
    usb_test util 16 firmware_upgrade To upgrade the firmware. util 17 enable_auto_backup 18 util enable_config_encryp Enables/Disables support. Configuration encryption 19 util
  • D-Link DSR-1000AC | Emulator - Page 37
    net bandwidth 13 traffic_selector delete It allows to delete a traffic selector for a bandwidth profile. 14 net ddns DDNS setup. 15 net ddns wan1 DDNS setup. 16 net ddns wan2 DDNS setup. 17 net ddns wan1 configure DDNS configuration mode. 18 net ddns wan2 configure DDNS
  • D-Link DSR-1000AC | Emulator - Page 38
    44 net ip_Aliasing Net policy mode. 45 net ip_Aliasing server Net policy mode. 46 net ip_Aliasing server add Adding Ip Aliasing server configuration 47 net ip_Aliasing server edit Editing Ip Aliasing server configuration. 48 net ip_Aliasing server delete Deleting Ip
  • D-Link DSR-1000AC | Emulator - Page 39
    77 net wan wan1 ipv6 Displays ipv6 wan configuration mode 78 net wan wan1 ipv6 configure Displays ipv6 wan1 configuration mode 79 net wan wan2 ipv6 Displays ipv6 wan2 configuration mode 80 net wan wan2 ipv6 configure Displays ipv6 wan2 configuration mode 81 net routing ospfv2 Displays OSPF
  • D-Link DSR-1000AC | Emulator - Page 40
    all the configured IPv6 routes. 109 net tahi Settings for tahi test suite. 110 net tahi add-defaultroute Adds ipv6 default 000) Starts 30000 sending RA with AdvReachableTime and AdvRetransTimer as 1000. as 118 net tahi start-RA- Starts sending RA with on the router. 40
  • D-Link DSR-1000AC | Emulator - Page 41
    132 net tahi ipv6-up Enables the ipv6 stack on the router. 133 net tahi ipv6-global-up Enables the ipv6 stack on the router, and adds global ip. 134 net tahi ipv6-AliasAdd(LAN) Adds ipv6 address to LAN interface. 135 net tahi ipv6-AliasDel(LAN) Deletes
  • D-Link DSR-1000AC | Emulator - Page 42
    To delete the selected application rule. 10 security firewall custom_service Custom Services Configuration setup. 11 security firewall custom_service add Custom services configuration add mode. security firewall 12 custom_service Custom services configuration edit mode. edit 42
  • D-Link DSR-1000AC | Emulator - Page 43
    security firewall 13 custom_service delete Custom services configuration delete mode. 14 security firewall Firewall rules setup. 15 security firewall ipv4 Firewall IPv4 rules setup. 16 security firewall ipv4 configure Firewall IPV4 rules
  • D-Link DSR-1000AC | Emulator - Page 44
    > To edit the selected mac address from the list. 60 security mac_filter source delete To delete the selected mac address. 61 security ip_or_mac_binding To link to the ip/mac binding configuration add mode. 44
  • D-Link DSR-1000AC | Emulator - Page 45
    62 security ip_or_mac_binding To edit the selected rule in the ip/mac binding edit configuration page. 63 security ip_or_mac_binding delete To delete the selected rule/rules. 64 security firewall vpn_passthrough VPN Passthrough setup. 65 security firewall vpn_passthrough
  • D-Link DSR-1000AC | Emulator - Page 46
    Chapter 6. Configuration commands under branch VPN 6.1 vpn gre_tunnel add S.No Command Name Description Type and Description 1 save Saves system user configuration settings. 2 exit Saves system user configuration settings and exit current mode. 3 cancel To revert to the previous system
  • D-Link DSR-1000AC | Emulator - Page 47
    6.2 vpn gre_tunnel edit S.No Command Name Description Type and Description 1 GRE Tunnel configuration mode Unsigned integer 2 save Saves system user configuration settings. 3 exit Saves system user configuration settings and exit current mode. 4 cancel To revert to
  • D-Link DSR-1000AC | Emulator - Page 48
    6.4 vpn l2tp client configure S.No Command Name Description Type and Description 1 save Saves l2tp client configuration settings. 2 cancel To revert to the previous settings. 3 exit Saves l2tp client configuration settings, and exit current mode. 4 enable Enables/disables L2TP client.
  • D-Link DSR-1000AC | Emulator - Page 49
    MS-CHAP authentication. Boolean choice 15 EnableMSChapv2 Enables MS-CHAPv2 authentication. Boolean choice Enables/Disables support 16 l2tpSecretKeyEnabl for Secret Key, and enters e Secret Key if support is Boolean choice enabled. 17 secretKey Enter L2TP secret Key if Secret Key is
  • D-Link DSR-1000AC | Emulator - Page 50
    6.7 vpn openvpn config S.No Command Name Description Type and Description 1 save Saves openvpn configuration settings. 2 cancel To revert to previous settings openvpn configuration settings 3 exit Saves openvpn configuration settings, and exit current mode. 4 enable Enables/disables
  • D-Link DSR-1000AC | Emulator - Page 51
    S.No Command Name Description Type and Description authenticate.packets. E.g.: SHA1, SHA256 and SHA512. SHA1 is the default. Selects Full Tunnel to redirect all the traffic through the tunnel. Select Split Tunnel to redirect 16 tunnel_type traffic to only specified type of tunnel resources (
  • D-Link DSR-1000AC | Emulator - Page 52
    6.8 vpn openvpn remote_network add S.No Command Name Description Type and Description 1 save Saves Remote network Configuration settings. 2 cancel To revert to previous settings. 3 exit Saves Remote network configuration settings, and exits current mode. 4 common_name Common Name of
  • D-Link DSR-1000AC | Emulator - Page 53
    6.10 vpn openvpn remote_network delete S.No Command Name Description Type and Description 1 Openvpn remote delete mode. network Unsigned integer 6.11 vpn openvpn local_network add S.No 1 2 3 4 5 Command Name save cancel exit local_network local_netmask Description Save
  • D-Link DSR-1000AC | Emulator - Page 54
    6.13 vpn openvpn local_network delete S.No Command Name Description 1 Deletes the selected openvpn Local network. Type and Description Unsigned integer 6.14 vpn openvpn cert_upload ca S.No Command Name Description 1 >
  • D-Link DSR-1000AC | Emulator - Page 55
    6.17 vpn openvpn cert_upload dh_Key S.No Command Name Description Type and Description String 1 Diffie Hellman key. AAA.BBB.CCC.DDD where each part is in the range 0-255 6.18 vpn openvpn cert_upload tls_Authkey <
  • D-Link DSR-1000AC | Emulator - Page 56
    6.21 vpn pptp client configure S.No Command Name Description Type and Description 1 save Saves pptp client configuration settings. 2 cancel To revert to previous PPTP Client configuration settings. 3 exit Saves pptp client configuration settings, and exits current mode. 4 enable
  • D-Link DSR-1000AC | Emulator - Page 57
    type of authentication required. Authentication type 12 pap_enable Enables support for PAP authentication method. Boolean choice 13 chap_enable Enables support for CHAP authentication method. Boolean choice Enables support for MS- 14 mschap_enable CHAP authentication Boolean choice method
  • D-Link DSR-1000AC | Emulator - Page 58
    be String, 'character is not displaysed along with the supported; banner title. Specifies whether the 9 display_banner banner message choice 14 sslAuthType Selects the authentication type for the portal. Supported authentication type 15 SSL_GROUP Selects a group name for the portal
  • D-Link DSR-1000AC | Emulator - Page 59
    characters, ' is Specifies the banner 8 banner_message message that would be displayed along with the String, ' character is not supported; banner title. Specifies whether the 9 display_banner banner message and banner title should be Boolean choice displayed. 10 enable_httpmetatag
  • D-Link DSR-1000AC | Emulator - Page 60
    6.26 vpn sslvpn portal-layouts delete S.No Command Name Description 1 Deletes sslvpn portal layout. Type and Description Unsigned integer 6.27 vpn sslvpn portforwarding appconfig add S.No Command Name Description Type and Description 1 save Saves portforwarding Apps
  • D-Link DSR-1000AC | Emulator - Page 61
    3 cancel To revert to previous sslvpn resource settings. 4 resource_name resource name String, MAX 128 characters, ' is not supported; 5 service_type service type Sslvpn resource. 6.32 vpn sslvpn resource configure add S.No Command Name Description Type and Description
  • D-Link DSR-1000AC | Emulator - Page 62
    type. Sslvpn policy type. 5 policy_owner Shows policy owner String 6 destination_objectty pe destination object type Sslvpn policy destination type. 7 policy_name policy name String, character is not supported; 62
  • D-Link DSR-1000AC | Emulator - Page 63
    32 10 start_port start port Port number 11 end_port end port Port number 12 service_type service type sslvpn resource 13 resource_name resource name String, MAX 128 characters, ' is not supported; 14 policy_permission This can Deny. be either Permit or sslvpn policy type 15 icmp
  • D-Link DSR-1000AC | Emulator - Page 64
    6.37 vpn sslvpn policy delete S.No Command Name Description Type and Description 1 Deletes an sslvpn policy Unsigned integer. 6.38 vpn sslvpn client S.No Command Name Description Type and Description 1 save Saves sslvpn client settings 2 exit Saves sslvpn client
  • D-Link DSR-1000AC | Emulator - Page 65
    vpn policy configuration settings. 4 exit Saves vpn policy configuration settings, and exits current mode. 5 general_policy_type Setting policy manual or auto. Vpn policy type. 6 general_ike_version Setting version ikev1 or ikev2. IPsec VPN IKE Version. 7 general_ip_protocol Setting
  • D-Link DSR-1000AC | Emulator - Page 66
    S.No Command Name Description Type and Description 12 general_remote_end _point fqdn The IP address or Internet Name/FQDN of the remote gateway or client PC. String. Enables/disables mode 13 general_enable_mo de_config config which is similar to DHCP and is used to assign IP addresses to
  • D-Link DSR-1000AC | Emulator - Page 67
    or IPV6. 33 general_keepalive_d estinationip keepalive destinationip IPV4 or IPv6 address depending upon protocol selected IPV4 or IPV6. Router sends ping packets 34 general_keepalive_d periodically at regular Keepalive detection period in etection_period intervals of time which is seconds
  • D-Link DSR-1000AC | Emulator - Page 68
    S.No Command Name Description Type and Description 38 manual_spi_out Takes a hexadecimal between 3 and 8 characters. value Takes a hexadecimal value between 3 and 8 characters. 39 manual_encryption_ The algorithm used to algorithm encrypt the data. Vpn encryption algorithm. 40
  • D-Link DSR-1000AC | Emulator - Page 69
    S.No 55 56 57 58 59 60 61 62 63 64 65 66 67 Command Name Description auto_phase1_encry Setting IKE encryption ption_algorithm DES algorithm. auto_phase1_encry ption_algorithm DES enable_DES Enables DES algorithm. encryption auto_phase1_encry ption_algorithm 3DES Setting IKE encryption
  • D-Link DSR-1000AC | Emulator - Page 70
    S.No Command Name Description Type and Description 68 auto_phase1_encry ption_algorithm CAST128 Setting IKE encryption algorithm. auto_phase1_encry 69 ption_algorithm CAST128 Enables CAST128 encryption algorithm. Boolean choice enable_CAST128 auto_phase1_encry 70 ption_algorithm Enter
  • D-Link DSR-1000AC | Emulator - Page 71
    S.No Command Name Description Type and Description 86 auto_phase1_enabl e_dead_peer_detect ion Enabling/Disabling peer detection. dead Boolean choice 87 auto_phase1_detect ion_period Setting dead time period. peer detection Unsigned integer 88 auto_phase1_recon nect_failure_count
  • D-Link DSR-1000AC | Emulator - Page 72
    S.No Command Name Description 103 auto_phase2_encry ption_algorithm AES-192 Setting IKE encryption algorithm. auto_phase2_encry 104 ption_algorithm AES-192 Enables AES-192 encryption algorithm. enable_AES-192 105 auto_phase2_encry ption_algorithm AES-256 Setting IKE encryption algorithm.
  • D-Link DSR-1000AC | Emulator - Page 73
    S.No Command Name Description Type and Description auto_phase2_encry 115 ption_algorithm BLOWFISH Enters BLOWFISH keylength. keylength Unsigned integer 116 auto_phase2_encry ption_algorithm CAST128 Setting IKE encryption algorithm. auto_phase2_encry 117 ption_algorithm CAST128 Enables
  • D-Link DSR-1000AC | Emulator - Page 74
    S.No Command Name Description Type and Description 132 auto_phase2_enabl e_pfskeygroup Enables/DIsables PFS key group. Boolean choice 133 auto_phase2_dh_gr Setting IKE Diffie-Hellman IPsec VPN IKE Diffie-Hellman oup (DH) Group. (DH) Group type 6.42 vpn ipsec dhcp configure S.No 1 2 3 4 5
  • D-Link DSR-1000AC | Emulator - Page 75
    6.46 vpn ipsec policy connect S.No Command Name Description 1 Connects a vpn tunnel Type and Description String 6.47 vpn ipsec policy drop S.No Command Name Description Type and Description 1 Drops/Disconnects a vpn tunnel String 75
  • D-Link DSR-1000AC | Emulator - Page 76
    Chapter 7. Configuration commands under branch DOT11 7.1 dot11 profile add S.No Command Name Description Type and Description 1 802.11 mode. profile configuration String 2 save Saves profile configuration settings. Saves profile configuration 3 exit
  • D-Link DSR-1000AC | Emulator - Page 77
    authentication is String PSK 7.3 dot11 wmm edit S.No 1 2 Command Name save Description The name of the profile to which service is being added will be displayed here. 802.11 wmm configuration mode. Saves wmm configuration settings. Type and Description String 77
  • D-Link DSR-1000AC | Emulator - Page 78
    current mode. 4 enable Enables/Disables the 802.11 profile wmm. Boolean choice Choose among "Background", "Best Effort", "video", "Voice". This class of service is used for the 5 default_class traffic for whose IP Dot11 WMM class DSCP/TOS value is set to "Default" in IP TOS/DiffServ
  • D-Link DSR-1000AC | Emulator - Page 79
    S.No Command Name Description 35 dscp_29 Selects class of ip dscp. 36 dscp_30 Selects class of ip dscp. 37 dscp_31 Selects class of ip dscp. 38 dscp_32 Selects class of ip dscp. 39 dscp_33 Selects class of ip dscp. 40 dscp_34 Selects class of ip dscp. 41 dscp_35 Selects class of ip
  • D-Link DSR-1000AC | Emulator - Page 80
    S.No 2 3 4 5 6 7 8 9 Command Name cancel exit primary_server secondary_server port secret timeout retries Description To revert to the previous radius configuration settings Saves ACL configuration settings and exit current mode. Sets Radius Primary authentication Server. Sets Radius Seconadry
  • D-Link DSR-1000AC | Emulator - Page 81
    7.6 dot11 accesspoint add S.No Command Name Description Type and Description 1 802.11 access point configuration mode. String 2 save Saves AP configuration settings. 3 cancel To revert to the previous AP configuration settings. 4 exit Saves AP configuration
  • D-Link DSR-1000AC | Emulator - Page 82
    S.No Command Name Description Type and Description 6 wlan_partition Enables or Disables wlan_partition. Boolean choice 7 enable_active_time Setting time. Boolean choice 8 enable_schedule_co ntrol Enables/disables Control. Schedule Boolean choice 9 start Setting the time limits. 10
  • D-Link DSR-1000AC | Emulator - Page 83
    7.11 dot11 wds add_peer S.No Command Name Description Type and Description Unsigned integer 1 wds. AA:BB:CC:DD:EE:FF where each part is in the range 00-FF 7.12 dot11 wds delete_peer S.No
  • D-Link DSR-1000AC | Emulator - Page 84
    S.No Command Name Description Type and Description 4 exit Saves radio configuration settings, and exit current mode. 5 channel Sets the channel used by radio. Dot11 Radio Channels. 6 default-transmitpower Sets the default transmit power for APs using this radio. Dot11 Radio default
  • D-Link DSR-1000AC | Emulator - Page 85
    S.No Command Name Description Type and Description Sets the 802.11b preamble 9 preamble_mode type to be prepended to 802.11b Preamble Types. every frame Enables/disables RTS/CTS 10 protection_mode handshake before packet RTSCTS Protection mode. transmission. Sets the retry limit for frame 11
  • D-Link DSR-1000AC | Emulator - Page 86
    S.No Command Name Description Type and Description 2 save Saves AP ACL configuration settings. 3 cancel To revert to the previous AP ACL configuration settings. 4 exit Saves the AP ACL configuration settings, and exit current mode. 5 acl_policy Sets the accesspoint ACL Policy.
  • D-Link DSR-1000AC | Emulator - Page 87
    Chapter 8. Configuration commands under branch SYSTEM 8.1 System NT-Domain-Settings S.No Command Name Description Type and Description save Saves NT Domain configuration settings. 2 exit Saves the NT Domain configuration settings and exit. 3 cancel To revert to the previous configuration
  • D-Link DSR-1000AC | Emulator - Page 88
    S.No 17 18 19 20 21 Command Name Description second_admin_host name Sets the NT Domain second server admin hostname. third_admin_name Sets the NT Domain third server admin name. third_admin_passwd Sets the NT Domain third server admin password. third_admin_hostna Sets the NT Domain third me
  • D-Link DSR-1000AC | Emulator - Page 89
    S.No Command Name Description Type and Description Sets the Active Directory 13 first_admin_passwd first server admin String password. 14 first_admin_hostna me Sets the Active Directory first server admin hostname. String 15 second_admin_nam e Sets the Active Directory second server
  • D-Link DSR-1000AC | Emulator - Page 90
    S.No Command Name Description Type and Description 7 LDAP_Base_DN Sets the LDAP Base DN. String 8 Second_LDAP_Bas e_DN Sets the second LDAP Base DN. alternative String 9 Third_LDAP_Base_ Sets the Third alternative DN LDAP Base DN. String 10 LDAPAttribute1 Sets the LDAP Attribute 1.
  • D-Link DSR-1000AC | Emulator - Page 91
    S.No Command Name Description Type and Description 6 Authentication_Serv er_3 Sets the optional server. String 7 Authentication_Port Sets the port for primary _1 server. Port number 8 Authentication_Port _2 Sets the port for secondary server. Port number 9 Authentication_Port Sets
  • D-Link DSR-1000AC | Emulator - Page 92
    S.No Command Name Description Type and Description 4 lan_wan_accept_pa LAN to wan accepted Pkts cket_logs Enable/Disable. Boolean choice 5 lan_wan_drop_pack LAN to wan dropped Pkts et_logs Enable/Disable. Boolean choice 6 wan_lan_accept_pa Wan to lan accepted Pkts cket_logs logs
  • D-Link DSR-1000AC | Emulator - Page 93
    8.7 system logging facility configure S.No Command Name Description Type and Description 1 System logging facility configuration mode. Logging Facility Type. 2 save Saves log Facility configuration settings. 3 exit Saves log facility configuration settings and exit
  • D-Link DSR-1000AC | Emulator - Page 94
    and String CRAM-MD5 auth). Sets SMTP authentication 15 smtp_auth password password (for plain and String CRAM-MD5 auth). Enables Tls support (for 16 Tls_Enable plain and CRAM-MD5 Boolean choice auth). 17 identd_from_smtp_s Enables/Diables to identd erver_enable from smtp server. Boolean
  • D-Link DSR-1000AC | Emulator - Page 95
    S.No Command Name Description 33 syslog_server server_name1 name Sets Syslog server. syslog_server 34 server_name1 severity syslog_server 35 server_name1 facility syslog_server 36 server_name2 enable Sets Syslog severity. Sets Syslog facility. Boolean Choice Y/N. 37 syslog_server
  • D-Link DSR-1000AC | Emulator - Page 96
    S.No Command Name Description syslog_server 48 server_name5 enable Boolean Choice Y/N. 49 syslog_server server_name5 name Sets Syslog server. syslog_server 50 server_name5 severity syslog_server 51 server_name5 facility syslog_server 52 server_name6 enable Sets Syslog severity. Sets Syslog
  • D-Link DSR-1000AC | Emulator - Page 97
    S.No Command Name Description syslog_server 63 server_name8 facility Sets Syslog facility. Type and Description Syslog server facility ID types. 8.9 system logging ipv6 configure S.No Command Name Description Type and Description 1 save Saves ipv6 logging configuration settings. 2 exit
  • D-Link DSR-1000AC | Emulator - Page 98
    S.No 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Command Name optional-radiusserver primary-serverauthentication-port secondary-serverauthentication-port optional-serverauthentication-port primary-serversecret secondary-serversecret optional-serversecret primary-servertimeout secondary-servertimeout
  • D-Link DSR-1000AC | Emulator - Page 99
    S.No 5 6 7 8 9 10 Command Name Description Type and Description type Enables/disables remote mgmt over https. Unsigned integer from_address Sets the starting IP in case of range, and the IP to be IP address allowed access in case of AAA.BBB.CCC.DDD where granting access to a each part is
  • D-Link DSR-1000AC | Emulator - Page 100
    8.13 system sessionSettings admin configure S.No Command Name Description Type and Description 1 save Saves Configurable WAN settings. 2 exit Saves configurable settings and exit current mode. 3 cancel To revert to the previous Configurable Session settings settings. 4 SessionTimeout
  • D-Link DSR-1000AC | Emulator - Page 101
    S.No Command Name Description Type and Description 7 port SNMP trap port the trap messages will be sent to. Port number 8 community The community string to which the agent belongs. Most agents are configured String to listen for traps in the Public community. 8.16 system snmp trap delete <
  • D-Link DSR-1000AC | Emulator - Page 102
    8.18 system snmp sys configure S.No 1 2 3 4 5 6 Command Name Description save Saves SNMP system configuration settings. cancel To revert to the previous snmp configuration settings. Saves SNMP system exit configuration settings and exit current mode. sys-contact Sets system contact
  • D-Link DSR-1000AC | Emulator - Page 103
    S.No Command Name Description Type and Description 7 community The community string to which the agent belongs. Most agents are configured String to listen for traps in the Public community 8.20 system snmp access edit S.No Command Name Description Type and Description 1
  • D-Link DSR-1000AC | Emulator - Page 104
    current mode. To revert to the previous 3 cancel content Filtering ower mode configuration settings. 4 link_status Enables/Disables Link status Boolean choice 5 cable_length Enables/Disables Cable Length Boolean choice 8.23 system switch_settings jumbo_frame configure S.No Command
  • D-Link DSR-1000AC | Emulator - Page 105
    8.24 system admin_setting configure S.No Command Name Description 1 save Saves system admin settings. 2 exit Saves configuration settings, and exit current mode. 3 cancel To revert to the previous admin configuration settings. 4 System_name Type and Description String 8.25 system time
  • D-Link DSR-1000AC | Emulator - Page 106
    8.26 system traffic_meter configure S.No Command Name Description Type and Description 1 save Saves traffic meter configuration settings. 2 exit Saves traffic meter configuration settings and exit current mode. 3 cancel To revert to the previous traffic meter configuration settings. 4
  • D-Link DSR-1000AC | Emulator - Page 107
    S.No Command Name Description Type and Description 2 exit Saves configurable WAN settings and exit current mode. 3 cancel To revert to the previous Configurable WAN settings settings. 4 enable Enables USB1 Boolean choice 5 printer_enable Enables printer usb Boolean choice 6
  • D-Link DSR-1000AC | Emulator - Page 108
    S.No Command Name Description Type and Description 4 cancel To revert to the previous shareport on vlan settings. 5 printer_sharing Enables printer Boolean choice 6 storage_sharing Enables USB2 Boolean choice 8.30 system group add S.No Command Name Description Type and Description 1
  • D-Link DSR-1000AC | Emulator - Page 109
    S.No Command Name Description Type and Description 2 save Saves system group configuration settings. 3 exit Saves system group configuration settings and exit current mode. 4 cancel To revert to the previous system group configuration settings. 5 description Enter a brief description
  • D-Link DSR-1000AC | Emulator - Page 110
    8.34 system users edit S.No Command Name Description Type and Description 1 System users edit mode. Unsigned integer 2 save Saves system user configuration settings. 3 exit Saves system user configuration settings and exit current mode. 4 cancel To revert to the
  • D-Link DSR-1000AC | Emulator - Page 111
    revert to the previous group access control browser configuration settings. 4 group_id group id Unsigned integer 5 browser_name browser name Supported browsers 8.38 system group access_control_browser delete S.No Command Name Description 1 Deletes a browser from Access
  • D-Link DSR-1000AC | Emulator - Page 112
    S.No Command Name Description 3 cancel To revert to the previous group access control ip configuration settings. 4 group_id group id 5 address_type address type 6 source_address Sets the source address. 7 mask_length Sets the source network mask length. Type and Description Unsigned
  • D-Link DSR-1000AC | Emulator - Page 113
    traceroute S.No Command Name Description Type and Description Displays all the routers 1 present between the destination IP address and String this router. 9.4 util system_check capturePackets start S.No Command Name Description Type and Description
  • D-Link DSR-1000AC | Emulator - Page 114
    Command Name Description 1 To test the USB. Type and Description String FileName string 9.8 1 To upgrade the firmware. Type and Description IP address AAA.BBB.CCC Enables/Disables Auto Backup support. Type and Description Boolean choice
  • D-Link DSR-1000AC | Emulator - Page 115
    Chapter 10. Configuration commands under branch LICENSE 10.1 license list S.No Command Name Description Type and Description 1 list Lists all licenses configured on the device. 2 activate Activates a license on the device. 10.2 license activate S.No Command Name
  • D-Link DSR-1000AC | Emulator - Page 116
    Chapter 11. Configuration commands under branch NET 11.1 net ipv6_tunnel six_to_four configure S.No 1 2 3 4 Command Name Description Type and Description save Saves sixToFour Tunnel configuration settings. Saves sixToFour Tunnel exit configuration settings, and exits current mode. To
  • D-Link DSR-1000AC | Emulator - Page 117
    S.No Command Name Description Type and Description 6 type Profile Type, either Priority or Rate. Bandwidth profile type. 7 priority Priority. Bandwidth priority type. 8 minimum_rate Minimum Bandwidth provided by user. Minimum bandwidth rate 0Max bandwidth Kbps. 9 maximum_rate Maximum
  • D-Link DSR-1000AC | Emulator - Page 118
    exit current mode. To revert to the previous 3 cancel Traffic Selector configuration settings. 4 profile_name Profile Name. String 5 service_name To see available services list by show command. String 6 match_type The match type can be IP or MAC Address. Traffic selector match type
  • D-Link DSR-1000AC | Emulator - Page 119
    mode. To revert to the previous 4 cancel Traffic Selector configuration settings. 5 profile_name Profile Name. String 6 service_name Sees available services list by show command String 7 match_type IP /MAC Address Traffic selector match type. 8 ip_address IP Address. IP address
  • D-Link DSR-1000AC | Emulator - Page 120
    . 3 cancel To revert to the previous DDNS configuration settings. 4 ddns_service Enables or Disables Dyndns to provide Dynamic Select the Ddns Service type. DNS service 5 hostname Sets Hostname. String, Max 64 characters and no ' or empty space or " 6 username Sets username. String, Max 64
  • D-Link DSR-1000AC | Emulator - Page 121
    S.No Command Name Description 8 time_update_enable Sets Timeperiod days. as 30 9 wild_flag_enable Enables/Disables using wild cards. Type and Description Boolean choice Boolean choice 11.11 net lan dhcp reserved_ip configure S.No Command Name Description Type and
  • D-Link DSR-1000AC | Emulator - Page 122
    11.13 net dmz dhcp reserved_ip configure S.No Command Name Description Type and Description 1 DHCP Reserved IPs add/edit mode. MAC address AA:BB:CC:DD:EE:FF where each part is in the range 00-FF 2 save Saves DHCP Reserved IPs configuration settings. 3 exit
  • D-Link DSR-1000AC | Emulator - Page 123
    S.No Command Name Description 6 native-vlan Enables/Disables native VLAN status. 7 vlanid Sets VLAN Id. Type and Description Boolean choice Unsigned integer 11.16 net lan ipv4 configure S.No Command Name Description Type and Description 1 save Saves LAN configuration settings. 2 exit
  • D-Link DSR-1000AC | Emulator - Page 124
    S.No Command Name Description Type and Description 16 dhcp domain_name Sets dhcp domain name. String, Max 256 characters and no ' or empty space or " 17 dhcp relay_gateway Sets dhcp relays gateway address. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255 18 dns Configures
  • D-Link DSR-1000AC | Emulator - Page 125
    S.No Command Name Description dns host_name 35 mapping 4 host_name Sets Host Name. dns host_name 36 mapping 4 ipaddress Sets Host Name. dns host_name 37 mapping 5 Sets Host Name. host_name dns host_name 38 mapping 5 Sets Host Name. ipaddress dns host_name 39 mapping 6 host_name Sets
  • D-Link DSR-1000AC | Emulator - Page 126
    S.No Command Name Description Type and Description 4 static Sets system LAN Settings. 5 static address Sets system LAN IP address. IP address abcd:abcd:abcd:abcd:abcd:abc d:abcd:abcd where each part is in the range [0-9A-Fa-f:] 6 static prefix_value Prefix length Unsigned integer 7 dhcp
  • D-Link DSR-1000AC | Emulator - Page 127
    S.No Command Name Description 6 end_address Sets dhcpv6 end IP address. 7 prefix_value Prefix length Type and Description IP address abcd:abcd:abcd:abcd:abcd:abc d:abcd:abcd where each part is in the range [0-9A-Fa-f:] Unsigned integer 11.19 net lan ipv6 pool delete S.No
  • D-Link DSR-1000AC | Emulator - Page 128
    S.No Command Name Description Type and Description 4 enable_Intel_Amt Enables/disables Intel Amt Ports. Boolean choice. 5 Wan_hosts IntelAmt Wan Host Type. Intel Amt Wan Host type. 6 Wan_host_Address IntelAmt Wan Host Address. String. IP address 7 Internal_Address IntelAmt internal
  • D-Link DSR-1000AC | Emulator - Page 129
    S.No Command Name Description Type and Description 13 Intel_Amt_Reflector _srcport 16992 Enter source port value for 16992. Port number 14 Intel_Amt_Reflector _srcport 16993 Enter source port value for 16993. Port number 15 Intel_Amt_Reflector _srcport 16994 Enter source port value for
  • D-Link DSR-1000AC | Emulator - Page 130
    S.No Command Name Description Type and Description 5 Interface Select the Interface for the Ip Aliasing WAN interface type 6 Ip_Address IP address Ip Address for ip Aliasing. AAA.BBB.CCC.DDD where each part is in the range 0-255. 7 Subnet_Mask Subnet mask for ip Aliasing. IP address AAA.
  • D-Link DSR-1000AC | Emulator - Page 131
    prefix that is assigned to the logical ISATAP subnet String for this intranet. This is the endpoint address for the tunnel that starts with this router. The 5 end_point_type endpoint can be the LAN Select the local end point interface (assuming the address type. LAN is an IPv4 network), or
  • D-Link DSR-1000AC | Emulator - Page 132
    S.No Command Name Description Type and Description This is the endpoint address for the tunnel that starts with this router. The 6 end_point_type endpoint can be the LAN Select the local end point interface (assuming the address type. LAN is an IPv4 network), or a specific LAN
  • D-Link DSR-1000AC | Emulator - Page 133
    if you have not been assigned any static IP address. The 6 dhcpc get_dns_from_isp ISP will automatically assign a DNS address to the router using DHCP Boolean choice. network protocol. Otherwise Enter No and give valid static dns addresses 7 dhcpc primary_dns Valid primary DNS Server IP
  • D-Link DSR-1000AC | Emulator - Page 134
    to you. This will each part is in the range 0-255. identify the router to your ISP. 14 static subnet_mask IPv4 Subnet Mask. usually provided by or Max 16 characters and no ' or empty space or ". 23 pppoe service Enter the password to authenticate. String. 24 pppoe authOpt Enter the Auth
  • D-Link DSR-1000AC | Emulator - Page 135
    have not been assigned any static IP address. The 30 pppoe get_ip_from_isp ISP will automatically assign an IP address to the Boolean choice router using PPPOE network protocol. Otherwise Enter No and give valid static IP address. 31 pppoe static_ip Enter valid IP Address. IP address AAA
  • D-Link DSR-1000AC | Emulator - Page 136
    ISP if you have not been assigned any static IP address. The 47 pptp get_dns_from_isp ISP will automatically assign a DNS address to the router using PPTP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 48 pptp primary_dns Enter valid primary DNS
  • D-Link DSR-1000AC | Emulator - Page 137
    S.No Command Name Description Type and Description 50 pptp mac_type Selects the Mac Address Source. Types of mac address source. MAC address 51 pptp mac_address Enter Valid MAC address. AA:BB:CC:DD:EE:FF where each part is in the range 00- FF. If ISP Type selected is Russian dual access
  • D-Link DSR-1000AC | Emulator - Page 138
    S.No Command Name Description Type and Description the router using PPTP network protocol. Otherwise Enter No and give valid static dns addresses. 65 russ_pptp primary_dns Enter a valid primary DNS Server IP Address IP address
  • D-Link DSR-1000AC | Emulator - Page 139
    ISP if you have not been assigned any static IP address. The 81 l2tp get_dns_from_isp ISP will automatically assign a DNS address to the router using L2TP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 82 l2tp primary_dns Valid primary DNS Server IP
  • D-Link DSR-1000AC | Emulator - Page 140
    if you have not been assigned any static IP address. The 98 russ_l2tp get_dns_from_isp ISP will automatically assign a DNS address to the router using L2TP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 99 russ_l2tp primary_dns Valid primary DNS
  • D-Link DSR-1000AC | Emulator - Page 141
    Description Type and Description japanese_pppoe 107 primary_profile service Enter the password to authenticate. String japanese_pppoe . The ISP will automatically assign an IP address to the Boolean choice router using PPPOE network protocol. Otherwise Enter No and give valid static IP
  • D-Link DSR-1000AC | Emulator - Page 142
    and no ' or empty space or " 120 japanese_pppoe secondary_profile service Enter the password to authenticate. String 121 japanese_pppoe secondary_profile authOpt assign a DNS address to Boolean choice get_dns_from_isp the router using PPPOE network protocol. Otherwise Enter No and give
  • D-Link DSR-1000AC | Emulator - Page 143
    and no ' or empty space or " 135 dual_pppoe service Enter the service to authenticate. String 136 dual_pppoe authOpt Enter the Auth The ISP will automatically assign an DNS address to Boolean choice the router using PPPOE network protocol. Otherwise Enter No and give valid static dns
  • D-Link DSR-1000AC | Emulator - Page 144
    Name Description Type and Description have not been assigned any static IP address. The ISP will automatically assign an IP address to the router using PPPOE network protocol. Otherwise Enter No and give valid static IP address. IP address 143 dual_pppoe static_ip Valid IP Address. AAA.BBB
  • D-Link DSR-1000AC | Emulator - Page 145
    ISP if you have not been assigned any static IP address. The 6 dhcpc get_dns_from_isp ISP will automatically assign a DNS address to the router using DHCP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses 7 dhcpc primary_dns Valid primary DNS Server IP
  • D-Link DSR-1000AC | Emulator - Page 146
    S.No Command Name Description Type and Description 8 dhcpc secondary_dns Valid secondary DNS Server IP Address. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. 9 dhcpc mac_type Select Mac Address source. Types of mac address source. 10 dhcpc mac_address Valid MAC address.
  • D-Link DSR-1000AC | Emulator - Page 147
    Command Name Description Type and Description 23 pppoe service Enter the password to authenticate. String 24 pppoe The 27 pppoe get_dns_from_isp ISP will automatically assign a DNS address to the router using PPPOE Boolean choice network protocol. Otherwise Enter No and give valid static
  • D-Link DSR-1000AC | Emulator - Page 148
    dynamically from ISP if you have not been assigned any static IP address. The 49 pptp get_dns_from_isp ISP will automatically assign a DNS address to the router using PPTP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 148
  • D-Link DSR-1000AC | Emulator - Page 149
    S.No Command Name Description Type and Description 50 pptp primary_dns Valid primary DNS Server IP Address. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. 51 pptp secondary_dns Valid secondary DNS Server IP Address. IP address AAA.BBB.CCC.DDD where each part is in the
  • D-Link DSR-1000AC | Emulator - Page 150
    if you have not been assigned any static IP address. The 66 russ_pptp get_dns_from_isp ISP will automatically assign a DNS address to the router using PPTP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 67 russ_pptp primary_dns Valid primary DNS
  • D-Link DSR-1000AC | Emulator - Page 151
    if you have not been assigned any static IP address. The 83 l2tp get_dns_from_isp ISP will automatically assign a DNS address to the router using L2TP Boolean choice network protocol. Otherwise Enter No and give valid static dns addresses. 84 l2tp primary_dns Valid primary DNS Server
  • D-Link DSR-1000AC | Emulator - Page 152
    not been assigned any static IP address. The 100 russ_l2tp get_dns_from_isp ISP will automatically assign a DNS address to Boolean choice. the router using L2TP network protocol. Otherwise Enter No and give valid static dns addresses. 101 russ_l2tp primary_dns Valid primary DNS Server IP
  • D-Link DSR-1000AC | Emulator - Page 153
    no ' or empty space or " japanese_pppoe 109 primary_profile service Enter the password to authenticate. String japanese_pppoe 110 primary_profile authOpt assign a DNS address to Boolean choice get_dns_from_isp the router using PPPOE network protocol. Otherwise Enter No and give
  • D-Link DSR-1000AC | Emulator - Page 154
    and no ' or empty space or " 122 japanese_pppoe secondary_profile service Enter the password to authenticate. String 123 japanese_pppoe secondary_profile authOpt assign a DNS address to Boolean choice. get_dns_from_isp the router using PPPOE network protocol. Otherwise Enter No and give
  • D-Link DSR-1000AC | Emulator - Page 155
    will automatically assign an IP address to the Boolean choice router using PPPOE network protocol. Otherwise Enter No and give valid and no ' or empty space or " 137 dual_pppoe service Enter the service to authenticate. String 138 dual_pppoe authOpt Enter the Auth authenticate
  • D-Link DSR-1000AC | Emulator - Page 156
    not been assigned 144 dual_pppoe get_ip_from_isp any static IP address. The ISP will automatically assign an IP address to the Boolean choice router using PPPOE network protocol. Otherwise Enter No and give valid static IP address. 145 dual_pppoe static_ip Valid IP Address. IP address
  • D-Link DSR-1000AC | Emulator - Page 157
    any static Dns dual_pppoe address. The internal ISP 153 get_dns_from_isp_p will automatically assign a Boolean choice. hy DNS address to the router using Dhcp network protocol. Otherwise Enter No and give valid static dns addresses. 154 dual_pppoe primary_dns_phy Valid primary DNS Server
  • D-Link DSR-1000AC | Emulator - Page 158
    S.No 165 166 Command Name Description threeg primary_dns Valid primary DNS Server IP Address. threeg secondary_dns Valid secondary DNS Server IP Address. Type and Description IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. IP address AAA.BBB.CCC.DDD where each part is in the
  • D-Link DSR-1000AC | Emulator - Page 159
    S.No Command Name Description Type and Description any static IP address. The ISP will automatically assign a DNS address to the router using THREEG network protocol. Otherwise Enter No and give valid static dns addresses. 12 Primary_dns Valid primary DNS Server IP Address. IP address AAA.
  • D-Link DSR-1000AC | Emulator - Page 160
    spillover max_bandwidth Primary WAN. If the bandwidth goes below the load tolerance value of Unsigned integer. configured Max Bandwidth, the router switches to secondary WAN. Sets the maximum bandwidth unit tolerable by 11 loadbalancing spillover max_bandwidth_unit the Primary WAN. If the
  • D-Link DSR-1000AC | Emulator - Page 161
    S.No Command Name Description Type and Description loadbalancing 21 failover_method retry_interval Idle timeout value type. loadbalancing 22 failover_method retry_attempts Number in range of 2 to 999. 23 rollover Wan Mode in Auto Rollover 24 rollover wan_port Selects the Auto rollover WAN
  • D-Link DSR-1000AC | Emulator - Page 162
    S.No Command Name Description 38 singleport 39 singleport wan_port Type and Description WAN interface type. 11.35 net wan port_setup configure S.No Command Name Description Type and Description 1 save Saves WAN port settings. 2 exit Saves WAN port settings and exit current mode. 3 cancel
  • D-Link DSR-1000AC | Emulator - Page 163
    S.No Command Name Description Type and Description 2 exit Saves WAN vlan Add settings and exit current mode. 3 cancel To revert to the previous WAN vlan settings settings. 4 vlan_Id Enter Vlan Id. Unsigned integer 11.38 net wan vlan_setup vlanId_Delete S.No Command Name Description
  • D-Link DSR-1000AC | Emulator - Page 164
    S.No Command Name Description Type and Description 3 exit Saves ipv6 wan1 configuration settings and current mode. 4 isp_type Sets the ISP Type. ISP Types. 5 dhcpc Sets the DHCPC Configurations. dhcpc 6 stateless_mode_ena Sets the Stateless Mode. Stateless mode configuration. ble
  • D-Link DSR-1000AC | Emulator - Page 165
    S.No Command Name Description 20 pppoe secondary_dns Valid secondary DNS Server IP Address. Type and Description IP address abcd:abcd:abcd:abcd:abcd:abc d:abcd:abcd where each part is in the range [0-9A-Fa-f:] 11.41 net wan wan2 ipv6 configure S.No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Command
  • D-Link DSR-1000AC | Emulator - Page 166
    /Disables OSPFv2 for a particular interface. Boolean choice 6 area Gives the area to which interface belongs. the Unsigned integer Helps to determine the OSPFv2 designated router for a network. The router with the highest priority will 7 priority be more eligible to become Designated
  • D-Link DSR-1000AC | Emulator - Page 167
    will be sent every 8 hello_interval timer value seconds on the specified interface. This Unsigned integer value must be the same for all routers attached to a common network. The default value is 10 seconds. 9 dead_interval The number of seconds that a device's hello packets must not have
  • D-Link DSR-1000AC | Emulator - Page 168
    value, Hello packet will be sent every timer value seconds on the specified interface. Unsigned integer This value must be the same for all routers attached to a common network. The default value is 10 seconds. The number of seconds that a device's hello packets must not have been seen before
  • D-Link DSR-1000AC | Emulator - Page 169
    Binding rules configuration settings and exit current mode. 3 cancel To revert to the previous configuration settings. 4 Service Available Service. service type 5 Local_Gateway Local gateway type. WAN interface type 6 Source_Network Source network type. Firewall rule address type
  • D-Link DSR-1000AC | Emulator - Page 170
    3 exit rules configuration settings and exit current mode. 4 cancel To revert to the previous configuration settings. 5 Service Available Service Service type. 6 Local_Gateway Local gateway type. WAN interface type. 7 Source_Network Source network type. Firewall rule address type
  • D-Link DSR-1000AC | Emulator - Page 171
    3 exit rules configuration settings and exit current mode. 4 cancel To revert to the previous configuration settings. 5 Service Available Service. Service type. 6 Local_Gateway Local gateway type. WAN interface type. 7 Source_Network Source network type. Firewall rule address type
  • D-Link DSR-1000AC | Emulator - Page 172
    To revert to the previous configuration settings. 5 Service Available Service Service type. 6 Local_Gateway Local gateway type. WAN interface choice of the IPv6 LAN network. 5 mode Selects N to send router advertisements (RA's) to interfaces, else Y. all Radvd type. advertizement
  • D-Link DSR-1000AC | Emulator - Page 173
    of other (i.e. non- Boolean choice address) information auto configuration. 10 preference Selects low/medium/high for the preference associated with this router's Radvd preference type. RADVD process. 11 mtu This is used in RA’s to ensure all nodes on the network value in use
  • D-Link DSR-1000AC | Emulator - Page 174
    Unsigned integer bits of the address that make up the network portion of the address. The length of time over 8 prefix_life_time which the requesting router Unsigned integer is allowed to use the prefix. 11.51 net radvd pool edit S.No Command Name Description Type and Description
  • D-Link DSR-1000AC | Emulator - Page 175
    Name Description Type and Description make up the network portion of the address. The length of time over 9 prefix_life_time which the requesting router Unsigned integer is allowed to use the prefix. 11.52 net radvd pool delete S.No Command Name Description Type and Description
  • D-Link DSR-1000AC | Emulator - Page 176
    S.No Command Name Description Type and Description 14 first_key valid_from hour Hour in which md5 authentication key validity starts. HH(00-23) using 24 hour clock 15 first_key valid_from minute Minute in which md5 authentication key validity starts. Minute in the format MM(0059.) 16
  • D-Link DSR-1000AC | Emulator - Page 177
    S.No 31 32 33 34 35 36 37 38 39 40 Command Name Description second_key valid_from year Year in which md5 authentication key validity starts. second_key valid_from hour Hour in which md5 authentication key validity starts. second_key valid_from minute Minute in which md5 authentication key
  • D-Link DSR-1000AC | Emulator - Page 178
    S.No Command Name Description Type and Description 6 subnet_mask Sets the subnet for this rule. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255 7 gateway_address Sets the gateway IP. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255 8 interface Sets the
  • D-Link DSR-1000AC | Emulator - Page 179
    S.No Command Name Description 9 metric Sets the metric for this route. 10 active_flag Defines whether its an active IPV6 route Type and Description Unsigned integer Boolean choice 11.56 net routing static ipv4 delete S.No Command Name Description 1 Deletes a specific IPv4
  • D-Link DSR-1000AC | Emulator - Page 180
    S.No Command Name Description Type and Description in the range [0-9A-Fa-f:] IP address abcd:abcd:abcd:abcd:abcd:abc d:abcd:abcd where each part is in the range [0-9A-Fa-f:] 11.61 net tahi ipv6-AliasAdd(LAN) S.No 1 Command Name Description Adds ipv6 address to LAN
  • D-Link DSR-1000AC | Emulator - Page 181
    S.No Command Name Description Type and Description d:abcd:abcd where each part is in the range [0-9A-Fa-f:] 11.65 net tahi reachable-time S.No Command Name Description Type and Description 1 Sets the reachable time of neighbour cache entries number in range of 30 to 150 11.66
  • D-Link DSR-1000AC | Emulator - Page 182
    11.70 net tahi interface-down S.No Command Name Description 1 Brings selected interface down. Type and Description Interfaces type 11.71 net tahi interface-up S.No Command Name Description 1 Brings selected interface up. Type and Description
  • D-Link DSR-1000AC | Emulator - Page 183
    S.No Command Name Description Type and Description 10 AdvOtherConfigFlag Sets AdvOtherConfigFlag value. Boolean choice 11 AdvDefaultLifetime Sets AdvDefaultLifetime value. AdvDefaultLifetime range 12 AdvReachableTime Sets AdvReachableTime value. AdvReachableTime range 13
  • D-Link DSR-1000AC | Emulator - Page 184
    11.75 net upnp configure S.No Command Name Description Type and Description 1 save Saves upnp configuration settings. 2 cancel To revert to the previous upnp configuration settings. 3 exit Saves upnp configuration settings and current mode. 4 enable Enables/Disables UPNP. Boolean
  • D-Link DSR-1000AC | Emulator - Page 185
    S.No Command Name Description 4 cancel To revert to the previous configuration settings. 5 mode Port Vlan mode. 6 pvid Port Vlan ID Type and Description Captive Portal Profile ID vlan id possible values 11.78 net vlan-membership lan_edit S.No Command Name Description Type and
  • D-Link DSR-1000AC | Emulator - Page 186
    S.No Command Name Description Type and Description 4 exit Saves vlan membership configuration settings and exit current mode. 5 membership Vlan membership.Give comma seperated VLAN ID values. Vlan membership.Give 6 membership add comma seperated VLAN ID String values. Vlan membership.
  • D-Link DSR-1000AC | Emulator - Page 187
    S.No Command Name Description Type and Description 12 secondary-dns IP address Secondary dns for the vlan. AAA.BBB.CCC.DDD where each part is in the range 0-255 13 default_gw Sets default gateway. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255 14 lease-time Lease time for
  • D-Link DSR-1000AC | Emulator - Page 188
    11.82 net vlan config edit S.No Command Name Description Type and Description 1 Edits a configured vlan. vlan id possible values 2 save Saves vlan configuration settings. 3 exit Saves vlan settings and exit current mode. 4 cancel To revert to the previous
  • D-Link DSR-1000AC | Emulator - Page 189
    S.No Command Name Description Type and Description 5 ip_address Static IP address. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. 6 subnet_mask Subnet Mask. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. 7 dhcp_mode Sets the DHCP mode. dhcpv4 modes
  • D-Link DSR-1000AC | Emulator - Page 190
    Chapter 12. Configuration commands under branch SECURITY 12.1 security advanced_network attack_checks configure S.No Command Name Description Type and Description 1 save Saves Security Checks configuration settings. 2 exit Saves Security Checks configuration settings and exit current mode.
  • D-Link DSR-1000AC | Emulator - Page 191
    S.No Command Name Description Type and Description 15 block_spoofed_tcp_r st Enables or Disables blocking of spoofed tcp RST packets. Boolean choice 16 block_ftp_bounce_at tack Enables or Disables blocking of FTP Bounce Attack packets. Boolean choice 17 echostorm_flood_rat Configures the
  • D-Link DSR-1000AC | Emulator - Page 192
    S.No Command Name Description 3 cancel To revert to the previous application rules configuration settings. 4 name Name of the rule. Type and Description String 5 enable_rule Specifies whether to Enable or Disable the rule. Boolean choice 6 protocol Specifies whether the port uses the
  • D-Link DSR-1000AC | Emulator - Page 193
    . Port type can be Port Range/Multiple Ports. The 6 type layer 3 Protocol that the Type to be selected for a service uses. Can be TCP, custom service. UDP, BOTH, ICMP or ICMPv6 7 start_port Port number of the Destination user. Port number 8 icmp_type Port number of the Destination user
  • D-Link DSR-1000AC | Emulator - Page 194
    be for added. String 6 protocol Protocol. Type of protocol to be selected for a custom service. 7 type Port type can be Port Range/Multiple Ports. Type to be selected for a custom service. 8 start_port Port number of the Destination user. Port number 9 icmp_type Port number of the
  • D-Link DSR-1000AC | Emulator - Page 195
    for which a rule is to be added. Custom name String should already be added into custom service 10 service service_normal Name which of the a rule service is to be for added. Service type. 11 action Action to be taken by the rule. Firewall rule action type. 12 schedule Name which
  • D-Link DSR-1000AC | Emulator - Page 196
    the Destination user. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255 21 qos_priority Firewall type of service. firewall type of service 22 wan_interface WAN interface for Source NAT settings. WAN interface type IP address 23 snat_address IP of the SNAT Address. AAA.BBB
  • D-Link DSR-1000AC | Emulator - Page 197
    for which a rule is to be added. Custom name String should already be added into custom service. 11 service service_normal Name which of the a rule service is to be for added. Service type. 12 action Action to be taken by the rule. Firewall rule action type. 13 schedule Name which
  • D-Link DSR-1000AC | Emulator - Page 198
    the Destiation user. IP address AAA.BBB.CCC.DDD where each part is in the range 0-255. 22 qos_priority Firewall type of service. Firewall type of service. 23 wan_interface WAN interface for Source NAT settings. WAN interface type. IP address 24 snat_address IP of the SNAT Address. AAA.BBB
  • D-Link DSR-1000AC | Emulator - Page 199
    12.13 security firewall ipv4 disable S.No Command Name Description Type and Description 1 Disables Firewall IPv4 Rules configuration mode. Unsigned integer 12.14 security firewall ipv4 delete S.No Command Name Description Type and Description 1 Deletes
  • D-Link DSR-1000AC | Emulator - Page 200
    for which a rule is to be added; custom name String should already be added into custom service. 7 service service_normal Name which of the a rule service is to be for added. Service type. 8 action Action to be taken by the rule. Firewall rule action type. 9 schedule Schedule for
  • D-Link DSR-1000AC | Emulator - Page 201
    for which a rule is to be added custom name String should already be added into custom service. 8 service service_normal Name which of the a rule service is to be for added. Service type. 9 action Action to be taken by the rule. Firewall rule action type. 10 schedule Schedule for
  • D-Link DSR-1000AC | Emulator - Page 202
    S.No Command Name Description Type and Description d:abcd:abcd where each part is in the range [0-9A-Fa-f:] IP address 15 source_end_addres s End IP of the Source user. abcd:abcd:abcd:abcd:abcd:abc d:abcd:abcd where each part is in the range [0-9A-Fa-f:] 16 source_address_pre Prefix length
  • D-Link DSR-1000AC | Emulator - Page 203
    S.No Command Name Description Type and Description 2 save Saves Firewall IPV6 rule reordering settings. 3 exit Saves Firewall IPV6 rule reordering settings and exit current mode. 4 cancel To revert to the previous IPV6 rule reordering settings. 5 position New position for the rule.
  • D-Link DSR-1000AC | Emulator - Page 204
    S.No Command Name Description 2 exit Saves session settings configuration settings and exit current mode. 3 cancel To revert to the previous session settings configuration settings. 4 max_unidentified_se Maximum Unidentified ssions Sessions. 5 max_half_open_ses Maximum Half Open sions
  • D-Link DSR-1000AC | Emulator - Page 205
    S.No Command Name Description Checks the box for each 9 days wednesday day to include in this schedule. 10 days thursday Checks the box for each day to include in this schedule. Checks the box for each 11 days friday day to include in this schedule. Checks the box for each 12 days
  • D-Link DSR-1000AC | Emulator - Page 206
    S.No Command Name Description Type and Description 3 exit Saves schedules configuration settings and exit current mode. 4 cancel To revert to the previous schedules configuration settings. 5 name Name of the schedule for which a rule is to be added String 6 days The days when the
  • D-Link DSR-1000AC | Emulator - Page 207
    S.No Command Name Description 20 time_of_day start meridiem meridiem 21 time_of_day end The end time for the schedule 22 time_of_day end mins minutes 23 time_of_day end hours hours 24 time_of_day end meridiem meridiem Type and Description Schedule Meridiem Types. Minute in the format
  • D-Link DSR-1000AC | Emulator - Page 208
    S.No Command Name Description 3 cancel To revert to the previous ApprovedMailId configuration settings. 4 approved_Mail_Id Approved Mail_Id Type and Description String 12.31 security firewall smtpAlg approvedMailId edit S.No Command Name Description 1 It allows to edit
  • D-Link DSR-1000AC | Emulator - Page 209
    12.34 security firewall smtpAlg blockedMailId edit S.No Command Name Description Type and Description 1 It allows to edit a blocked MailId. Unsigned integer 2 save Saves BlockedMailId configuration settings. Saves BlockedMailId 3 exit configuration settings and exit
  • D-Link DSR-1000AC | Emulator - Page 210
    12.37 security firewall smtpAlg subjectList edit S.No Command Name Description Type and Description 1 It allows to MailId and edit subject action. with Unsigned integer 2 save Saves subjectList configuration settings. Saves subjectList 3 exit configuration settings
  • D-Link DSR-1000AC | Emulator - Page 211
    12.40 security mac_filter source add S.No Command Name Description 1 save Saves source mac filter configuration settings. 2 exit Saves source mac filter configuration settings and exit current mode. 3 cancel To revert to the previous source mac filter configuration settings. 4 address
  • D-Link DSR-1000AC | Emulator - Page 212
    12.43 security ip_or_mac_binding add S.No Command Name 1 save 2 exit 3 cancel 4 computer_name 5 mac_address 6 ip_address 7 log_dropped_packets Description Type and Description Saves ip mac binding configuration settings. Saves ip mac binding configuration settings and exit current mode. To
  • D-Link DSR-1000AC | Emulator - Page 213
    S.No Command Name Description Type and Description 8 log_dropped_packet s Specifies this rule. logging option for Boolean choice 12.45 security ip_or_mac_binding delete S.No Command Name Description Type and Description 1 Deletes binding the selected ip/mac
  • D-Link DSR-1000AC | Emulator - Page 214
    S.No Command Name Description 2 exit Saves webAccess rules configuration settings and exit current mode. 3 cancel To revert to the previous webAccess rules configuration settings. 4 name Name 5 accessType AcessType 6 ipAddr 7 vlanId IpAddr VlanId Type and Description String Access
  • D-Link DSR-1000AC | Emulator - Page 215
    12.51 security website_filter content_filtering configure S.No Command Name Description Type and Description 1 save Saves contentFiltering configuration settings. 2 exit Saves content Filtering configuration settings and exit current mode. To revert to the previous 3 cancel content
  • D-Link DSR-1000AC | Emulator - Page 216
    S.No Command Name Description 3 exit Saves trusted domains configuration settings and exit current mode. 4 cancel To revert to the previous trusted domains configuration settings. 5 url Trusted domain name. Type and Description String 12.54 security website_filter approved_urls delete <
  • D-Link DSR-1000AC | Emulator - Page 217
    S.No Command Name Description 4 cancel To revert to the previous blocked keywords configuration settings. 5 blocked_keyword Enter keyword to be blocked. Type and Description String 12.57 security website_filter blocked_keywords delete S.No Command Name Description 1
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217

CLI Reference Guide
Unified Services Router
D-Link Corporation
Copyright © 2015.