Dell PowerConnect W-IAP92 Dell Instant 5.0.3.0-1.1.0.0 User Guide - Page 129

Mobility Trail, Association Time, Access Point

Get Dell PowerConnect W-IAP92 PDF manuals and user guides View all Dell PowerConnect W-IAP92 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

Table 17 Client View - RF Trends Graphs and Monitoring Procedures (Continued) Graph Name Description Monitoring Procedure Throughput The Throughput Graph shows the throughput for the selected client for the last 15 minutes.  Outgoing traffic - Throughput for outgoing traffic is displayed in green. Outgoing traffic is shown above the median line.  Incoming traffic - Throughput for incoming traffic is displayed in blue. Incoming traffic is shown below the median line. To see an enlarged view, click the graph.  The enlarged view shows Last, Minimum, Maximum, and Average statistics for the incoming and outgoing traffic throughput of the client for the last 15 minutes. To see the exact throughput at a particular time, hover the cursor over the graph line. To monitor the errors for the client for the last 15 minutes, 1. Log in to the Instant UI. The Virtual Controller view appears. This is the default view. 2. In the Clients tab, click the IP address of the client for which you want to monitor the throughput. The client view appears. 3. Study the Throughput graph in the RF Trends pane. For example, the graph on the left shows 1.0 kbps outgoing traffic throughput for the client at 12:30 hours. Mobility Trail The Mobility Trail section displays the following mobility trail information for the selected client:  Association Time - The time at which the selected client was associated with a particular IAP. It shows the client-IAP association for the last 15 minutes.  Access Point - IAP name with which the client was associated. NOTE: Mobility information about the client is reset each time it roams from one IAP to another. Dell PowerConnect W-Instant Access Point 5.0.3.0-1.1.0.0 | User Guide Monitoring | 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Dell PowerConnect W-Instant Access Point 5.0.3.0-1.1.0.0
| User Guide
Monitoring
|
129
Mobility Trail
The
Mobility Trail
section displays the following mobility trail information for the selected client:
Association Time
- The time at which the selected client was associated with a particular IAP. It shows the
client-IAP association for the last 15 minutes.
Access Point
- IAP name with which the client was associated.
Throughput
The Throughput Graph shows the throughput for
the selected client for the last 15 minutes.
Outgoing traffic - Throughput for outgoing
traffic is displayed in green. Outgoing traffic
is shown above the median line.
Incoming traffic - Throughput for incoming
traffic is displayed in blue. Incoming traffic
is shown below the median line.
To see an enlarged view, click the graph.
The enlarged view shows Last, Minimum,
Maximum, and Average statistics for the
incoming and outgoing traffic throughput of
the client for the last 15 minutes.
To see the exact throughput at a particular time,
hover the cursor over the graph line.
To monitor the errors for the client for the last 15 minutes,
1.
Log in to the Instant UI. The Virtual Controller view
appears. This is the default view.
2.
In the Clients tab, click the IP address of the client for
which you want to monitor the throughput. The client
view appears.
3.
Study the Throughput graph in the RF Trends pane.
For example, the graph on the left shows 1.0 kbps
outgoing traffic throughput for the client at 12:30
hours.
Table 17
Client View - RF Trends Graphs and Monitoring Procedures (Continued)
Graph Name
Description
Monitoring Procedure
NOTE:
Mobility information about the client is reset each time it roams from one IAP to another.