Dell PowerEdge 2900 Hardware Owner's Manual (PDF) - Page 131

Troubleshooting Expansion Cards - raid utility

Get Dell PowerEdge 2900 PDF manuals and user guides View all Dell PowerEdge 2900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

3 Restart the system and press the applicable key sequence to enter the configuration utility program: • for a SAS controller • for a SAS RAID controller See the controller's documentation for information about configuration settings. 4 Check the configuration settings, make any necessary corrections, and restart the system. If the problem is not resolved, continue to the next step. 5 Remove the bezel. See "Removing the Bezel" on page 50. 6 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet. 7 Open the system. See "Opening the System" on page 53. 8 Ensure that the controller card is firmly seated into the system board connector. See "SAS Controller Daughter Card" on page 96. 9 If you have a SAS RAID controller daughter card, ensure that the following RAID components are properly installed and connected: • Memory module • Battery 10 Verify that the cable connections between the SAS backplane(s) and the SAS controller daughter card are correct. See "Cabling the SAS Backplane Boards" on page 99. 11 Ensure that the cables are firmly connected to the SAS controller daughter card, the SAS backplane board and, if applicable, the 1x2 expansion backplane. 12 Close the system. See "Closing the System" on page 53. 13 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals. If the problem persists, proceed as follows: • If you have a SAS controller daughter card, see "Getting Help" on page 147. • If you have a SAS RAID controller daughter card, replace the SAS RAID daughter card battery. See "Replacing the SAS RAID Controller Daughter Card Battery" on page 96. If replacing the battery does not solve the problem, see "Getting Help" on page 147. Troubleshooting Expansion Cards NOTE: When troubleshooting an expansion card, see the documentation for your operating system and the expansion card. Problem • Error message indicates a problem with an expansion card. • Expansion card performs incorrectly or not at all. Troubleshooting Your System 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Troubleshooting Your System
131
3
Restart the system and press the applicable key sequence to enter the configuration utility program:
•
<Ctrl><C> for a SAS controller
•
<Ctrl><R> for a SAS RAID controller
See the controller's documentation for information about configuration settings.
4
Check the configuration settings, make any necessary corrections, and restart the system.
If the problem is not resolved, continue to the next step.
5
Remove the bezel. See "Removing the Bezel" on page 50.
6
Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.
7
Open the system. See "Opening the System" on page 53.
8
Ensure that the controller card is firmly seated into the system board connector. See "SAS Controller
Daughter Card" on page 96.
9
If you have a SAS RAID controller daughter card, ensure that the following RAID components are
properly installed and connected:
•
Memory module
•
Battery
10
Verify that the cable connections between the SAS backplane(s) and the SAS controller daughter card
are correct. See "Cabling the SAS Backplane Boards" on page 99.
11
Ensure that the cables are firmly connected to the SAS controller daughter card, the SAS backplane
board and, if applicable, the 1x2 expansion backplane.
12
Close the system. See "Closing the System" on page 53.
13
Reconnect the system to its electrical outlet, and turn on the system and attached peripherals. If the
problem persists, proceed as follows:
•
If you have a SAS controller daughter card,
see "Getting Help" on page 147.
•
If you have a SAS RAID controller daughter card, replace the SAS RAID daughter card battery
.
See
"Replacing the SAS RAID Controller Daughter Card Battery" on page 96. If replacing the battery
does not solve the problem,
see "Getting Help" on page 147.
Troubleshooting Expansion Cards
NOTE:
When troubleshooting an expansion card, see the documentation for your operating system and the
expansion card.
Problem
•
Error message indicates a problem with an expansion card.
•
Expansion card performs incorrectly or not at all.