Dell PowerEdge 2900 Hardware Owner's Manual (PDF) - Page 94

Optional 1x2 Flex Bay Drive Bracket

Get Dell PowerEdge 2900 PDF manuals and user guides View all Dell PowerEdge 2900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

9 Replace the front bezel, if removed. 10 Reconnect the system to the electrical outlet and turn on the system and attached peripherals. Optional 1x2 Flex Bay Drive Bracket Removing the 1x2 Flex Bay Drive Bracket CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 1 Remove the front bezel, if attached. See "Removing the Bezel" on page 50. 2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3 Open the system. See "Opening the System" on page 53. 4 Push the latch on top of the peripheral bay to the right to release the flex bay bracket and push the back of the flex bay bracket partially out of the chassis. See Figure 3-26. 5 Note the order of SAS cable connections on the flex bay backplane and disconnect the SAS cables. See Figure 3-26. 6 Disconnect the power cable from the flex bay backplane. See Figure 3-26. 7 Remove the 1x2 flex bay drive bracket from the chassis bay. 94 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
94
Installing System Components
9
Replace the front bezel, if removed.
10
Reconnect the system to the electrical outlet and turn on the system and attached peripherals.
Optional 1x2 Flex Bay Drive Bracket
Removing the 1x2 Flex Bay Drive Bracket
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. See your
Product Information Guide
for complete information about safety
precautions, working inside the computer, and protecting against electrostatic discharge.
1
Remove the front bezel, if attached. See
"Removing the Bezel" on page 50
.
2
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and
peripherals.
3
Open the system. See
"Opening the System" on page 53
.
4
Push the latch on top of the peripheral bay to the right to release the flex bay bracket and push the
back of the flex bay bracket partially out of the chassis. See
Figure 3-26
.
5
Note the order of SAS cable connections on the flex bay backplane and disconnect the SAS cables.
See
Figure 3-26
.
6
Disconnect the power cable from the flex bay backplane. See
Figure 3-26
.
7
Remove the 1x2 flex bay drive bracket from the chassis bay.