Dell PowerEdge R7525 EMC Installation and Service Manual - Page 131

Installing the full length expansion card risers

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Installing the full length expansion card risers Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 40. 2. Follow the procedure listed in Before working inside your system on page 41. 3. If removed, install the GPU into the expansion card risers. Steps 1. To install the full length expansion card Risers 1A and 3A: a. Connect the GPU cable to the system board. b. Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board. c. Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector. d. Tighten the captive screws on the risers and system if any. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Figure 94. Installing the expansion card riser (Riser 1A) Installing and removing system components 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Installing the full length expansion card risers
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 40.
2.
Follow the procedure listed in
Before working inside your system
on page 41.
3.
If removed,
install the GPU into the expansion card risers
.
Steps
1.
To install the full length expansion card Risers 1A and 3A:
a.
Connect the GPU cable to the system board.
b.
Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
c.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the
system board connector.
d.
Tighten the captive screws on the risers and system if any.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 94. Installing the expansion card riser (Riser 1A)
Installing and removing system components
131