Dell PowerEdge R7525 EMC Installation and Service Manual - Page 47

Control panel, Removing the right control panel

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Figure 23. Installing the drive backplane cover Next steps 1. Follow the procedure listed in After working inside your system on page 41. Control panel Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 40. 2. Follow the procedure listed in the Before working inside your system on page 41. 3. Remove the drive backplane cover. 4. If installed, remove the air shroud. 5. Remove the cooling fan assembly. 6. Remove the side wall bracket. Steps 1. Using the Phillips #1 screwdriver, remove the screws that secure the right control panel and the right control panels cable cover to the system and remove the cable cover away the system. 2. Disconnect the right control panel cable and the VGA cable from the connectors on the system board. 3. Holding the cable, slide the right control panel out of the system. NOTE: Observe the routing of the cable as you remove the right control panel from the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Installing and removing system components 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Figure 23. Installing the drive backplane cover
Next steps
1.
Follow the procedure listed in
After working inside your system
on page 41.
Control panel
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 40.
2.
Follow the procedure listed in the
Before working inside your system
on page 41.
3.
Remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Remove the cooling fan assembly
.
6.
Remove the side wall bracket
.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws that secure the right control panel and the right control panels cable cover to the
system and remove the cable cover away the system.
2.
Disconnect the right control panel cable and the VGA cable from the connectors on the system board.
3.
Holding the cable, slide the right control panel out of the system.
NOTE:
Observe the routing of the cable as you remove the right control panel from the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Installing and removing system components
47