Dell PowerEdge R7525 EMC Installation and Service Manual - Page 16

Inside the system

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Table 6. Rear view of the system with 2 x 2.5-inch rear drive module (continued) Item Ports, panels, or slots Icon Description To reset iDRAC, press and hold the button for more than 16 seconds. NOTE: • To reset iDRAC using system ID, ensure that the system ID button is enabled in the iDRAC setup. • If the system stops responding during POST, press and hold the system ID button (for more than 5 seconds) to enter the BIOS progress mode. 12 OCP NIC port (optional) N/A 13 NIC port (1,2) 14 Power supply unit (PSU 1) This port supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board. The NIC ports are embedded on the LOM card that is connected to the system board. For more information about the PSU configurations, see the Technical Specifications section. For more information about the ports, see the Technical Specifications section. Inside the system Figure 11. Inside the system 1. Handle 3. Power supply unit (PSU 1) 16 System overview 2. Riser 1 blank 4. Riser 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Table 6. Rear view of the system with 2 x 2.5-inch rear drive module (continued)
Item
Ports, panels, or slots
Icon
Description
To reset iDRAC, press and hold the button for more than 16 seconds.
NOTE:
•
To reset iDRAC using system ID, ensure that the system
ID button is enabled in the iDRAC setup.
•
If the system stops responding during POST, press and
hold the system ID button (for more than 5 seconds) to
enter the BIOS progress mode.
12
OCP NIC port (optional)
N/A
This port supports OCP 3.0. The NIC ports are integrated on the OCP
card which is connected to the system board.
13
NIC port (1,2)
The NIC ports are embedded on the LOM card that is connected to the
system board.
14
Power supply unit (PSU 1)
For more information about the PSU configurations, see the
Technical
Specifications
section.
For more information about the ports, see the
Technical Specifications
section.
Inside the system
Figure 11. Inside the system
1.
Handle
2.
Riser 1 blank
3.
Power supply unit (PSU 1)
4.
Riser 2
16
System overview