Dell PowerEdge R7525 EMC Installation and Service Manual - Page 62

Installing the side wall bracket

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Figure 38. Removing the side wall bracket Next steps 1. Replace the side wall bracket. Installing the side wall bracket Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 40. 2. Follow the procedure listed in the Before working inside your system on page 41. 3. If installed, remove the front bezel. 4. Remove the backplane cover. 5. If installed, remove the air shroud. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped. Steps 1. Align the side wall bracket with the tabs on the chassis. 2. Press the side wall bracket with your thumbs until the bracket firmly clicks into place. NOTE: Route the cables through the side wall bracket. 3. Close the side wall bracket cover with your thumbs until the cover firmly clicks into place. 62 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Figure 38. Removing the side wall bracket
Next steps
1.
Replace the side wall bracket
.
Installing the side wall bracket
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 40.
2.
Follow the procedure listed in the
Before working inside your system
on page 41.
3.
If installed,
remove the front bezel
.
4.
Remove the backplane cover
.
5.
If installed,
remove the air shroud
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. Route the cable
properly when you replace it to prevent the cable from being pinched or crimped.
Steps
1.
Align the side wall bracket with the tabs on the chassis.
2.
Press the side wall bracket with your thumbs until the bracket firmly clicks into place.
NOTE:
Route the cables through the side wall bracket.
3.
Close the side wall bracket cover with your thumbs until the cover firmly clicks into place.
62
Installing and removing system components