Dell PowerEdge R7525 EMC Installation and Service Manual - Page 78

Front PERC module, Removing the front mounting front PERC module

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Figure 62. Installing the rear drive cage Next steps 1. Replace the expansion card riser, if needed. 2. Connect all the cables to the rear drive cage. 3. Install all the drives. 4. Follow the procedure listed in After working inside your system on page 41. Front PERC module Removing the front mounting front PERC module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 40. 2. Follow the procedure listed in the Before working inside your system on page 41. 3. remove the backplane cover. 4. If installed, remove the air shroud. 5. Disconnect all the cables, observe the cable routing. Steps 1. Using a Phillips #2 screwdriver, loosen the captive screws on the front PERC module. 2. Slide and pull the front PERC module to disengage from the connector on the drive backplane. 78 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Figure 62. Installing the rear drive cage
Next steps
1.
Replace the
expansion card riser
, if needed.
2.
Connect all the cables to the rear drive cage.
3.
Install all the drives
.
4.
Follow the procedure listed in
After working inside your system
on page 41.
Front PERC module
Removing the front mounting front PERC module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 40.
2.
Follow the procedure listed in the
Before working inside your system
on page 41.
3.
remove the backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Disconnect all the cables, observe the cable routing.
Steps
1.
Using a Phillips #2 screwdriver, loosen the captive screws on the front PERC module.
2.
Slide and pull the front PERC module to disengage from the connector on the drive backplane.
78
Installing and removing system components