Dell PowerEdge R7525 EMC Installation and Service Manual - Page 48

Installing the right control panel

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Figure 24. Removing the right control panel Next steps 1. Replace the right control panel. Installing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 40. 2. Follow the procedure listed in Before working inside your system on page 41. Steps 1. Align and slide the right control panel in the slot on the system. 2. Connect the right control panel cable and VGA cable to the connectors on the system board. 3. Route the right control panel cable through the side wall of the system. Align and slide the right control panel cable cover in the slot on the system. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 4. Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel and the right control panel cable cover to the system. 48 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Figure 24. Removing the right control panel
Next steps
1.
Replace the right control panel
.
Installing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 40.
2.
Follow the procedure listed in
Before working inside your system
on page 41.
Steps
1.
Align and slide the right control panel in the slot on the system.
2.
Connect the right control panel cable and VGA cable to the connectors on the system board.
3.
Route the right control panel cable through the side wall of the system. Align and slide the right control panel cable cover in the slot on
the system.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
4.
Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel and the right control panel cable cover to the
system.
48
Installing and removing system components