Dell PowerEdge R7525 EMC Installation and Service Manual - Page 95

Expansion cards and expansion card risers, Expansion card installation guidelines

Get Dell PowerEdge R7525 PDF manuals and user guides View all Dell PowerEdge R7525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Figure 78. Installing the heat sink Next steps 1. If removed, install the air shroud. 2. Follow the procedure listed in the After working inside your system on page 41. Expansion cards and expansion card risers NOTE: A system event entry is logged in the iDRAC Lifecycle Controller if an expansion card riser is not supported or missing. It does not prevent your system from turning on. However, if a F1/F2 pause occurs with an error message, see Troubleshooting expansion cards section in the Dell EMC PowerEdge Servers Troubleshooting Guide at www.dell.com/ poweredgemanuals. Expansion card installation guidelines The following table describes the supported expansion cards: Table 39. Expansion card riser configurations Expansion card riser PCIe slots Processor connection Height Riser 1 Slot 1 Slot 2 Processor 1 Full Height Riser 2 Slot 3 Slot 6 Processor 1 Processor 2 Low Profile Riser 3 Slot 4 Slot 5 Processor 2 Full Height Length Half Length Half Length Half Length Slot width x8 x16 x8 x16 x16 x8 x8 x16 Installing and removing system components 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Figure 78. Installing the heat sink
Next steps
1.
If removed,
install the air shroud
.
2.
Follow the procedure listed in the
After working inside your system
on page 41.
Expansion cards and expansion card risers
NOTE:
A system event entry is logged in the iDRAC Lifecycle Controller if an expansion card riser is not supported or
missing. It does not prevent your system from turning on. However, if a F1/F2 pause occurs with an error message, see
Troubleshooting expansion cards
section in the
Dell EMC PowerEdge Servers Troubleshooting Guide
at
www.dell.com/
poweredgemanuals
.
Expansion card installation guidelines
The following table describes the supported expansion cards:
Table 39. Expansion card riser configurations
Expansion card riser
PCIe slots
Processor
connection
Height
Length
Slot
width
Riser 1
Slot 1
Processor 1
Full Height
Half Length
x8
x16
Slot 2
x8
x16
Riser 2
Slot 3
Processor 1
Low Profile
Half Length
x16
Slot 6
Processor 2
Riser 3
Slot 4
Processor 2
Full Height
Half Length
x8
x8
Slot 5
x16
Installing and removing system components
95