Dell S3100 Command Line Reference Guide for the Series 9.100.0 - Page 666

Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) 9.4(0.0) 9.2(1.0) 9.0.2.0 8.3.19.0 8.3.11.1 8.3.7.0 7.7.1.0 7.6.1.0 Introduced on the S3100 series. Introduced on the Z9100-ON. Introduced on the S4048-ON. Introduced on the S3048-ON. Introduced on the S6000-ON. Added support for VRF. Introduced on the Z9500. Introduced on the S6000. Introduced on the S4820T. Introduced on the Z9000. Introduced on the S4810. Added support for up to seven stack members. Introduced on the S-Series. Usage Information The following describes the show ip fib stack-unit command shown in the following example. Field Description Destination Gateway First-Hop Mac-Addr Port VId EC Lists the destination IP address. Displays either the word "direct" and an interface for a directly connected route or the remote IP address used to forward the traffic. Displays the first hop IP address. Displays the MAC address. Displays the egress-port information. Displays the VLAN ID. If no VLAN is assigned, zero (0) is listed. Displays the number of ECMP paths. If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named WEC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is assigned with a weight. Example Dell# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC 1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 0 2.1.1.2/32 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 0 0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 1.1.1.0/24 Direct, Vl 1000 0.0.0.0 00:00:00:00:00:00 CP 1000 0 1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 2.1.1.0/24 Direct, Vl 20 0.0.0.0 00:00:00:00:00:00 CP 20 0 2.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 100.1.1.0/24 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 1 100.1.1.0/24 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 1 Dell# Dell# show ip route S 10.1.1.0/24 S 20.1.1.0/24 S 100.1.1.0/24 via 1.1.1.2, Vl 10 via 2.1.1.2, Vl 20 via 3.1.1.2, Vl 30 via 10.1.1.0, weight 7 via 20.1.1.0, weight 1 Example (Show command output with Weighted ECMP Enabled) Dell# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC RC W 0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 - - 1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - - 1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 - - The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp weighted command. 666 IPv4 Routing