HP DL120 ProLiant DL120 Generation 5 Server Maintenance and Service Guide - Page 53

To install a memory module, but it does not fit easily into the slot

Get HP DL120 - ProLiant - G5 PDF manuals and user guides
UPC - 884962061909
View all HP DL120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

To install a memory module: 1. Perform the pre-installation procedure. 2. If necessary, remove any accessory boards or cables that prevent access to the DIMM slots. 3. Locate an empty DIMM slot on the system board. 4. If necessary, open the holding clips of the selected DIMM slot. 5. Remove the memory module from its protective packaging, handling it by the edges. 6. Install the memory module. a. Use both hands to hold the module by the edges, and then insert it perpendicularly into the slot (1). The DIMM slots are structured to ensure proper installation. If you insert a memory module but it does not fit easily into the slot, you may have inserted it incorrectly. Reverse the orientation of the module and insert it again. b. Press the module at both ends to seat it fully into the slot (2). The holding clips will automatically lock into place once the module has been seated properly. 7. Perform the post-installation procedure. Removal and replacement procedures 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Removal and replacement procedures
53
To install a memory module:
1.
Perform the pre-installation procedure.
2.
If necessary, remove any accessory boards or cables that prevent access to the DIMM slots.
3.
Locate an empty DIMM slot on the system board.
4.
If necessary, open the holding clips of the selected DIMM slot.
5.
Remove the memory module from its protective packaging, handling it by the edges.
6.
Install the memory module.
a.
Use both hands to hold the module by the edges, and then insert it perpendicularly into the
slot (
1
).
The DIMM slots are structured to ensure proper installation. If you insert a memory module
but it does not fit easily into the slot, you may have inserted it incorrectly. Reverse the
orientation of the module and insert it again.
b.
Press the module at both ends to seat it fully into the slot (
2
).
The holding clips will automatically lock into place once the module has been seated
properly.
7.
Perform the post-installation procedure.