HP DL120 ProLiant DL120 Generation 5 Server Maintenance and Service Guide - Page 62

To connect the SAS HDD and LED cables, Connect the SAS HDD cable.

Get HP DL120 - ProLiant - G5 PDF manuals and user guides
UPC - 884962061909
View all HP DL120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

4. Remove the controller board from its protective packaging, handling it by the edges. 5. Install the controller board. a. Slide the controller board into the slot (1). Make sure the board is properly seated in the slot. b. Secure the controller board with the one screw (2). 6. Reinstall the PCI riser board assembly to the chassis. 7. Proceed to the next section for instructions on how to connect the SAS HDD and LED cables. To connect the SAS HDD and LED cables: 1. Connect the SAS HDD cable. a. Connect the cable's master connector to the SAS controller board (1). b. Route the SAS cable lines underneath the PCI riser board assembly and through the drive cable opening of the center wall, and then secure the SAS cable lines in the chassis cable tie (2). Removal and replacement procedures 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Removal and replacement procedures
62
4.
Remove the controller board from its protective packaging, handling it by the edges.
5.
Install the controller board.
a.
Slide the controller board into the slot (
1
).
Make sure the board is properly seated in the slot.
b.
Secure the controller board with the one screw (
2
).
6.
Reinstall the PCI riser board assembly to the chassis.
7.
Proceed to the next section for instructions on how to connect the SAS HDD and LED cables.
To connect the SAS HDD and LED cables:
1.
Connect the SAS HDD cable.
a.
Connect the cable’s master connector to the SAS controller board (
1
).
b.
Route the SAS cable lines underneath the PCI riser board assembly and through the drive
cable opening of the center wall, and then secure the SAS cable lines in the chassis cable tie
(
2
).