HP DL120 ProLiant DL120 Generation 5 Server Maintenance and Service Guide - Page 58

Make sure the board is properly seated in the slot., Slide the expansion board into the slot

Page 58 highlights

4. Remove the expansion board from its protective packaging, handling it by the edges. Some expansion boards can only be installed in one slot but other boards can be configured to fit in either slot by replacing the default bracket (attached to the board) with a different sized one. The different sized bracket and instructions on how to attach it to the board is included in the option kit. 5. Verify that the board's default bracket is compatible with the configuration of the selected slot. If it is not compatible, replace the bracket with one that is compatible. 6. Install the expansion board. a. Slide the expansion board into the slot (1). Make sure the board is properly seated in the slot. b. Secure the expansion board with the one screw (2). 7. Reinstall the PCI riser board assembly to the chassis. 8. Connect the necessary cable(s) to the board. Refer to the documentation that came with the board. 9. Perform the post-installation procedure. Removal and replacement procedures 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108

Removal and replacement procedures
58
4.
Remove the expansion board from its protective packaging, handling it by the edges.
Some expansion boards can only be installed in one slot but other boards can be configured to
fit in either slot by replacing the default bracket (attached to the board) with a different sized
one. The different sized bracket and instructions on how to attach it to the board is included in
the option kit.
5.
Verify that the board’s default bracket is compatible with the configuration of the selected slot.
If it is not compatible, replace the bracket with one that is compatible.
6.
Install the expansion board.
a.
Slide the expansion board into the slot (
1
).
Make sure the board is properly seated in the slot.
b.
Secure the expansion board with the one screw (
2
).
7.
Reinstall the PCI riser board assembly to the chassis.
8.
Connect the necessary cable(s) to the board.
Refer to the documentation that came with the board.
9.
Perform the post-installation procedure.