HP DL120 ProLiant DL120 Generation 5 Server Maintenance and Service Guide - Page 61

Option kits, SAS controller board and SAS HDD/LED cables

Get HP DL120 - ProLiant - G5 PDF manuals and user guides
UPC - 884962061909
View all HP DL120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Option kits Refer to the following sections for instructions about how to install the SAS controller board, SAS HDD cable, SAS LED cable, PCI-X riser board, and Lights-Out 100c remote management card option kits. SAS controller board and SAS HDD/LED cables If you intend to change the system from a SATA to SAS configuration, first install the SAS controller board, and then connect the SAS HDD and LED cables. NOTE: Remove the SATA HDD cables from the chassis if you intend to install a SAS hard disk drive. To install the SAS controller board: 1. Remove the PCI riser board assembly. 2. Identify the riser board slot that is compatible with SAS controller board model you intend to install. 3. Prepare the selected slot for controller board installation. a. Remove the screw that secures the slot cover (1). Reuse this screw to install the controller board. b. Pull out the slot cover from the assembly (2). Store it for reassembly later. CAUTION: Do not discard the slot cover. If the controller board is removed in the future, the slot cover must be reinstalled to maintain proper cooling. Removal and replacement procedures 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Removal and replacement procedures
61
Option kits
Refer to the following sections for instructions about how to install the SAS controller board, SAS HDD
cable, SAS LED cable, PCI-X riser board, and Lights-Out 100c remote management card option kits.
SAS controller board and SAS HDD/LED cables
If you intend to change the system from a SATA to SAS configuration, first install the SAS controller
board, and then connect the SAS HDD and LED cables.
NOTE:
Remove the SATA HDD cables from the chassis if you intend to install a SAS hard disk drive.
To install the SAS controller board:
1.
Remove the
PCI riser board assembly.
2.
Identify the riser board slot that is compatible with SAS controller board model you intend to
install.
3.
Prepare the selected slot for controller board installation.
a.
Remove the screw that secures the slot cover (
1
).
Reuse this screw to install the controller board.
b.
Pull out the slot cover from the assembly (
2
).
Store it for reassembly later.
CAUTION:
Do not discard the slot cover. If the controller board is removed in the future, the
slot cover must be reinstalled to maintain proper cooling.