HP NetServer LP 2000r HP Netserver Ultra3 SCSI HBA Guide - Page 21

Configuration with SCSI

Get HP NetServer LP 2000r PDF manuals and user guides View all HP NetServer LP 2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

2 Configuration with SCSISelect SCSISelect, included with the HP Ultra3 SCSI Host Bus Adapter, enables you to change SCSI settings without opening the computer or handling the host bus adapter. SCSISelect also enables you to low-level format or verify the disk media of your SCSI hard disk drives. The following table lists the available and default settings for each SCSISelect option. NOTE The default settings are appropriate for most systems. Run SCSISelect if you need to change or view current settings, or if you would like to run the SCSI disk utilities. See the descriptions of each option starting on page 17. SCSISelect Options SCSI Bus Interface Definitions: Host Adapter SCSI ID SCSI Parity Checking Host Adapter SCSI Termination LVD/SE Connectors SE Connectors Boot Device Options: Boot SCSI ID Boot LUN Number1 SCSI Device Configuration: Sync Transfer Rate (MBytes/sec) Available Settings Default Setting 0-15 7 Enabled, Disabled Enabled Automatic, Enabled, Automatic Disabled Automatic Automatic Low ON/High ON Low OFF/High OFF Low OFF/High ON 0-15 0 0-7 0 160, 80.0, 53.4, 40.0, 160 32.0, 26.8, 20.0, 16.0, 13.4, 10.0, ASYN 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
15
2
Configuration with SCSI
Select
SCSI
Select,
included with the HP Ultra3 SCSI Host Bus Adapter, enables you
to change SCSI settings without opening the computer or handling the host bus
adapter. SCSI
Select
also enables you to low-level format or verify the disk
media of your SCSI hard disk drives. The following table lists the available and
default settings for each SCSI
Select
option.
NOTE
The default settings are appropriate for most systems. Run SCSI
Select
if you need to change or view current settings, or if you would like to
run the SCSI disk utilities. See the descriptions of each option starting
on page 17.
SCSI
Select
Options
Available
Settings
Default
Setting
SCSI Bus Interface Definitions:
Host Adapter SCSI ID
0-15
7
SCSI Parity Checking
Enabled, Disabled
Enabled
Host Adapter SCSI Termination
LVD/SE Connectors
Automatic, Enabled,
Disabled
Automatic
SE Connectors
Automatic
Low ON/High ON
Low OFF/High OFF
Low OFF/High ON
Automatic
Boot Device Options:
Boot SCSI ID
0-15
0
Boot LUN Number
1
0-7
0
SCSI Device Configuration:
Sync Transfer Rate (MBytes/sec)
160, 80.0, 53.4, 40.0,
32.0, 26.8, 20.0,
16.0, 13.4, 10.0,
ASYN
160