HP NetServer LP 2000r HP Netserver Ultra3 SCSI HBA Guide - Page 74

Installing the Driver When SCO OpenServer is, Already Installed

Get HP NetServer LP 2000r PDF manuals and user guides View all HP NetServer LP 2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

NOTE Remember that UNIX commands are case sensitive. Enter the commands exactly as shown in the instructions. 1. Insert the SCO OpenServer 5.0.x boot disk into the primary floppy disk drive and turn ON the computer. Alternatively, insert the SCO OpenServer 5.0.x boot CD into the primary CD-ROM drive and turn ON the computer. When you see these prompts: SCO OpenServer (TM) Release 5 Boot : Type ahslink and press Enter. (The boot drive should be ID0 or ID1.) 2. Type ad160 as the package you want to link to the system and press Enter. 3. Insert the requested volume (the Ultra3 Family Manager Set disk for SCO OpenServer) in the floppy disk drive and press Enter. 4. If the driver is properly loaded, the following message appears: ad160.adl60:Loading module fd(52)/ad160/driver/ad160/Driver.o text.... : : adl6O: Driver "adl6O" successfully loaded. 5. Follow the procedures in your SCO OpenServer documentation for completing the installation. Installing the Driver When SCO OpenServer is Already Installed To update or install the adl6O driver if SCO OpenServer is already installed, follow the instructions in this section. The procedures are similar for all versions of SCO OpenServer. Procedures that are specific to a SCO version are noted when necessary. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
68
NOTE
Remember that UNIX commands are case sensitive. Enter the
commands exactly as shown in the instructions.
1. Insert the SCO OpenServer 5.0.x boot disk into the primary floppy disk
drive and turn ON the computer. Alternatively, insert the SCO OpenServer
5.0.x boot CD into the primary CD-ROM drive and turn ON the computer.
When you see these prompts:
SCO OpenServer (TM) Release 5
Boot
:
Type
ahslink
and press Enter.
(The boot drive should be ID0 or ID1.)
2. Type
ad160
as the package you want to link to the system and press
Enter
.
3. Insert the requested volume (the Ultra3 Family Manager Set disk for SCO
OpenServer) in the floppy disk drive and press Enter.
4. If the driver is properly loaded, the following message appears:
ad160.adl60:Loading module
fd(52)/ad160/driver/ad160/Driver.o text
....
:
:
adl6O: Driver “adl6O” successfully loaded.
5. Follow the procedures in your SCO OpenServer documentation for
completing the installation.
Installing the Driver When SCO OpenServer is
Already Installed
To update or install the
adl6O
driver if SCO OpenServer is already installed,
follow the instructions in this section. The procedures are similar for all
versions of SCO OpenServer. Procedures that are specific to a SCO version are
noted when necessary.