HP NetServer LP 2000r HP Netserver Ultra3 SCSI HBA Guide - Page 79

Using SCO OpenServer and the Host Adapter

Get HP NetServer LP 2000r PDF manuals and user guides View all HP NetServer LP 2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

b Check the host bus adapter BIOS messages to verify that all your installed SCSI devices are listed. If some or all of your installed SCSI devices do not appear at this time, your SCSI cables may be loose, or the SCSI device setup may not be complete. If so, go back and correct any problem before proceeding. c Wait for UNIX to boot with the new kernel. See "Troubleshooting" on page 76 if the system crashes or if "panic" (UNIX error) messages are displayed at boot time. The adl60 driver for your HP Ultra3 SCSI host bus adapter should now be ready for use. Using SCO OpenServer and the Host Adapter This section contains useful information on using SCO OpenServer and your host bus adapter. Using Multiple Host Adapters If you are adding an additional HP Ultra3 SCSI host bus adapter to a system with an Ultra3 SCSI host bus adapter already installed, follow the instructions in the SCO OpenServer documentation for adding devices using the mkdev command. When the system asks for the host adapter prefix, type ad160 and press Enter. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
73
b
Check the host bus adapter BIOS messages to verify that all your installed SCSI
devices are listed.
If some or all of your installed SCSI devices do not appear at this time, your
SCSI cables may be loose, or the SCSI device setup may not be complete. If so,
go back and correct any problem before proceeding.
c
Wait for UNIX to boot with the new kernel.
See “Troubleshooting” on page 76 if the system crashes or if “panic” (UNIX
error) messages are displayed at boot time.
The
adl60
driver for your HP Ultra3 SCSI host bus adapter should now be
ready for use.
Using SCO OpenServer and the Host Adapter
This section contains useful information on using SCO OpenServer and your
host bus adapter.
Using Multiple Host Adapters
If you are adding an additional HP Ultra3 SCSI host bus adapter to a system
with an Ultra3 SCSI host bus adapter already installed, follow the instructions
in the SCO OpenServer documentation for adding devices using the
mkdev
command. When the system asks for the host adapter prefix, type
ad160
and
press
Enter
.