HP StorageWorks 300 HP StorageWorks 300 Virtual Library System user guide (AH1 - Page 134

Power supply zone fan module, Installing an AC power supply

Get HP StorageWorks 300 - Virtual Library System EVA Gateway PDF manuals and user guides View all HP StorageWorks 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

WARNING! To reduce the risk of electric shock or damage to the equipment, do not connect the power cord to the power supply until the power supply is installed. 1. Remove the protective cover from the connector pins on the power supply. 2. Slide the power supply into the bay until it clicks. Figure 76 Installing an AC power supply 3. Use the strain relief clip to secure the power cord (Figure 77). Figure 77 Placing the power cord in the strain relief clip 4. Connect the power cord to the power supply. 5. Be sure that the power supply LED is green. Power supply zone fan module CAUTION: Do not operate the node for long periods without the access panel. Operating the node without the access panel results in improper airflow and improper cooling that can lead to thermal damage. 1. Power off the node. See Powering off the system. 2. Extend or remove the node from the rack. See Extending the node from the rack. 3. Remove the access panel. See Removing the VLS node access panel. 4. Remove the SATA cable from the cable clip to avoid damaging the cable. 134 Component replacement

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
WARNING!
To reduce the risk of electric shock or damage to the equipment, do not connect the power cord to the
power supply until the power supply is installed.
1.
Remove the protective cover from the connector pins on the power supply.
2.
Slide the power supply into the bay until it clicks.
Figure 76 Installing an AC power supply
3.
Use the strain relief clip to secure the power cord (
Figure 77
).
Figure 77 Placing the power cord in the strain relief clip
4.
Connect the power cord to the power supply.
5.
Be sure that the power supply LED is green.
Power supply zone fan module
CAUTION:
Do not operate the node for long periods without the access panel. Operating the node without the
access panel results in improper air
fl
ow and improper cooling that can lead to thermal damage.
1.
Power off the node. See
Powering off the system
.
2.
Extend or remove the node from the rack. See
Extending the node from the rack
.
3.
Remove the access panel. See
Removing the VLS node access panel
.
4.
Remove the SATA cable from the cable clip to avoid damaging the cable.
134
Component replacement