HP StorageWorks 300 HP StorageWorks 300 Virtual Library System user guide (AH1 - Page 135

Processor zone fan module, Removing the node power supply zone fan module

Get HP StorageWorks 300 - Virtual Library System EVA Gateway PDF manuals and user guides View all HP StorageWorks 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

5. Push levers on either side of the middle fan toward the front of the chassis (1). Rock the fan module slightly and pull up and out of the node. 12 1 Figure 78 Removing the node power supply zone fan module CAUTION: When replacing the component, be sure the power converter module, which is located just in front of the fan module, is properly seated in the node chassis. To replace the component, reverse the removal procedure. Processor zone fan module CAUTION: Do not operate the node for long periods without the access panel. Operating the node without the access panel results in improper airflow and improper cooling that can lead to thermal damage. 1. Extend or remove the node from the rack. See Extending the node from the rack. 2. Remove the access panel. See Removing the VLS node access panel. 3. Loosen the single thumbscrew that secures the processor fan module to the node (1). 4. Push on the sheet metal tab near the thumbscrew to separate the fan tray connector from the system board connector (2). 5. Slide the component out the front of the node. HP StorageWorks 135

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
5.
Push levers on either side of the middle fan toward the front of the chassis (1). Rock the fan module
slightly and pull up and out of the node.
1
1
2
Figure 78 Removing the node power supply zone fan module
CAUTION:
When replacing the component, be sure the power converter module, which is located just in front of the
fan module, is properly seated in the node chassis.
To replace the component, reverse the removal procedure.
Processor zone fan module
CAUTION:
Do not operate the node for long periods without the access panel. Operating the node without the
access panel results in improper air
fl
ow and improper cooling that can lead to thermal damage.
1.
Extend or remove the node from the rack. See
Extending the node from the rack
.
2.
Remove the access panel. See
Removing the VLS node access panel
.
3.
Loosen the single thumbscrew that secures the processor fan module to the node (1).
4.
Push on the sheet metal tab near the thumbscrew to separate the fan tray connector from the system
board connector (2).
5.
Slide the component out the front of the node.
HP StorageWorks
135