HP StorageWorks 300 HP StorageWorks 300 Virtual Library System user guide (AH1 - Page 30

Installing VLS300 cables, Install switch 2824 in rack

Get HP StorageWorks 300 - Virtual Library System EVA Gateway PDF manuals and user guides View all HP StorageWorks 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

11193 Figure 7 Attach rails to switch 2824 2. Insert two of the pan-head screws through the slide rail and into the switch at the front of the switch. Tighten the screws. 3. Insert two of the pan-head screws through the appropriate holes in the slide rail and into the switch at the back of the switch. Tighten the screws. 4. Perform these steps again to Install the other rail on the other side of the node. Install switch 2824 in rack 1. Align the rails on the appliance with the rails in the rack. 2. Slide the appliance fully into the rack. The rails on the appliance will lock into the rails on the rack. 3. On each side of the switch, insert an MS screw through the holes in the rail and into the holes in the rack. 4. Tighten the MS screws to secure the switch to the rack. Installing VLS300 cables To install VLS300 cables, follow the instructions below. 1. On the primary node of the VLS300: 30 Hardware installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
11193
Figure 7 Attach rails to switch 2824
2.
Insert two of the pan-head screws through the slide rail and into the switch at the front of the
switch. Tighten the screws.
3.
Insert two of the pan-head screws through the appropriate holes in the slide rail and into the switch
at the back of the switch. Tighten the screws.
4.
Perform these steps again to Install the other rail on the other side of the node.
Install switch 2824 in rack
1.
Align the rails on the appliance with the rails in the rack.
2.
Slide the appliance fully into the rack.
The rails on the appliance will lock into the rails on the rack.
3.
On each side of the switch, insert an MS screw through the holes in the rail and into the holes
in the rack.
4.
Tighten the MS screws to secure the switch to the rack.
Installing VLS300 cables
To install VLS300 cables, follow the instructions below.
1.
On the primary node of the VLS300:
30
Hardware installation