HP StorageWorks 300 HP StorageWorks 300 Virtual Library System user guide (AH1 - Page 31

Primary node ports,

Get HP StorageWorks 300 - Virtual Library System EVA Gateway PDF manuals and user guides View all HP StorageWorks 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

12 34 10 11 5 6 78 9 11148 1 Dual port FC card, host port, port 0 2 Dual port FC card, host port, port 1 3 Dual port FC card, storage port, port 3 4 Dual port FC card, storage port, port 2 5 Serial port to access CLI 6 Monitor and keyboard 7 NIC1, on primary node only connects to the customer-provided external network (array) 8 NIC2, on primary node connects to port 1 of switch 2824 9 USB port, connects to USB/Ethernet adapter, then to port 1 of switch 2524 10 Power supply 2 11 Power supply 1 Figure 8 Primary node ports a. Connect one end of an Ethernet cable (not included) to NIC1. Connect the other end of the cable to the existing external network. b. Connect one end of an FC cable (not provided) to host port 0. Connect the other end to an external FC switch/fabric that connects to your tape backup hosts. c. If desired, connect one end of an FC cable (not provided) to host port 1. Connect the other end to an external FC switch/fabric that connects to your tape backup hosts. Otherwise, connect a loopback plug to host port 1. d. Connect one end of an FC cable (not provided) to device port 3. Connect the other end to an external FC switch/fabric that connects to your external array. e. Connect one end of an FC cable (not provided) to device port 2. Connect the other end to a second external FC switch/fabric that connects to your external array. f. Connect to the serial port (cable is provided) to access the command-line user interface at initial configuration. Also connect to this during debug activities. Disconnect from this port during normal operations. NOTE: You must connect to the keyboard and monitor ports when performing Quick Restore (keyboard and monitor not included). g. Connect one end of an Ethernet cable to NIC2. Connect the other end of the cable to port 1 of Switch 2824 (see Figure 10). h. Connect one end of a USB cable to the USB port. Connect the other end of the cable to the USB/Ethernet adapter. Connect an Ethernet cable to the Ethernet end of the adapter, then connect the Ethernet cable to port 1 of Switch 2524 (see Figure 11). i. Connect a power cable to each power supply and to a PDU. If possible, connect each power supply to a separate PDU to provide redundancy. HP StorageWorks 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
11148
5
10
11
1
2
3
4
6
7
8
9
1
Dual port FC card, host port, port 0
2
Dual port FC card, host port, port 1
3
Dual port FC card, storage port, port 3
4
Dual port FC card, storage port, port 2
5
Serial port to access CLI
6
Monitor and keyboard
7
NIC1, on primary node only connects to the customer-provided external network (array)
8
NIC2, on primary node connects to port 1 of switch 2824
9
USB port, connects to USB/Ethernet adapter, then to port 1 of switch 2524
10
Power supply 2
11
Power supply 1
Figure 8 Primary node ports
a.
Connect one end of an Ethernet cable (not included) to NIC1. Connect the other end of the
cable to the existing external network.
b.
Connect one end of an FC cable (not provided) to host port 0. Connect the other end to an
external FC switch/fabric that connects to your tape backup hosts.
c.
If desired, connect one end of an FC cable (not provided) to host port 1. Connect the other end
to an external FC switch/fabric that connects to your tape backup hosts. Otherwise, connect a
loopback plug to host port 1.
d.
Connect one end of an FC cable (not provided) to device port 3. Connect the other end to an
external FC switch/fabric that connects to your external array.
e.
Connect one end of an FC cable (not provided) to device port 2. Connect the other end to a
second external FC switch/fabric that connects to your external array.
f.
Connect to the serial port (cable is provided) to access the command-line user interface at initial
con
fi
guration. Also connect to this during debug activities. Disconnect from this port during
normal operations.
NOTE:
You must connect to the keyboard and monitor ports when performing Quick Restore
(keyboard and monitor not included).
g.
Connect one end of an Ethernet cable to NIC2. Connect the other end of the cable to port
1 of Switch 2824 (see
Figure 10
).
h.
Connect one end of a USB cable to the USB port. Connect the other end of the cable to the
USB/Ethernet adapter. Connect an Ethernet cable to the Ethernet end of the adapter, then
connect the Ethernet cable to port 1 of Switch 2524 (see
Figure 11
).
i.
Connect a power cable to each power supply and to a PDU. If possible, connect each power
supply to a separate PDU to provide redundancy.
HP StorageWorks
31