HP StorageWorks 300 HP StorageWorks 300 Virtual Library System user guide (AH1 - Page 144

Rebuilding the virtual library con, guration, Restore Con, g window

Get HP StorageWorks 300 - Virtual Library System EVA Gateway PDF manuals and user guides View all HP StorageWorks 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

a. Select the System tab. b. Select Nodes from the navigation tree. c. Select Add Node from the task bar in the main window. This will bring up the Add Node Wizard. d. Verify that the node name in the Node Name field is the next available number that you configured previously. For example, the primary node, previously configured as Node 0, is identified as Node 0 in the list of nodes on the navigation tree. The first secondary node added should be Node 1. The next secondary node added should be Node 2. e. Select Finish to add the node. 4. Select Chassis in the navigation tree. 5. Click Restore Config under Maintenance Taskss. The Restore Config window opens (Figure 87). Figure 87 Restore Config window 6. Click Browse. 7. Locate and select the desired configuration file. 8. Click Open. 9. Click Next Step. A message is displayed indicating that the file was uploaded successfully. 10. Click Next to start loading the configuration file. After the configuration file is loaded, the system automatically applies the configuration and reboots. Rebuilding the virtual library configuration To reconfigure the network settings and rebuild the virtual library configuration: 1. Set the network settings so you can open a Command View VLS session. See Setting the network settings. 2. Rebuild the virtual library and virtual drive configurations and re-enter your other configuration settings, such as the notification alert settings. See Configuration, Management, and Monitoring. 144 Disaster recovery

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
a.
Select the
System
tab.
b.
Select
Nodes
from the navigation tree.
c.
Select
Add Node
from the task bar in the main window. This will bring up the
Add Node Wizard
.
d.
Verify that the node name in the
Node Name
fi
eld is the next available number that you
con
fi
gured previously. For example, the primary node, previously con
fi
gured as Node 0, is
identi
fi
ed as Node 0 in the list of nodes on the navigation tree. The
fi
rst secondary node added
should be Node 1. The next secondary node added should be Node 2.
e.
Select
Finish
to add the node.
4.
Select
Chassis
in the navigation tree.
5.
Click
Restore Con
fi
g
under
Maintenance Tasks
s.
The Restore Con
fi
g window opens (
Figure 87
).
Figure 87 Restore Con
fi
g window
6.
Click
Browse
.
7.
Locate and select the desired con
fi
guration
fi
le.
8.
Click
Open
.
9.
Click
Next Step
.
A message is displayed indicating that the
fi
le was uploaded successfully.
10.
Click
Next
to start loading the con
fi
guration
fi
le.
After the con
fi
guration
fi
le is loaded, the system automatically applies the con
fi
guration and reboots.
Rebuilding the virtual library con
fi
guration
To recon
fi
gure the network settings and rebuild the virtual library con
fi
guration:
1.
Set the network settings so you can open a Command View VLS session. See
Setting the network
settings
.
2.
Rebuild the virtual library and virtual drive con
fi
gurations and re-enter your other con
fi
guration
settings, such as the noti
fi
cation alert settings. See
Con
fi
guration
,
Management
, and
Monitoring
.
144
Disaster recovery