HP t505 Administrator Guide - Page 28

Wired network settings, DNS settings, IPSec rules, Configuring VPN settings, Configuring HP Velocity

Get HP t505 PDF manuals and user guides View all HP t505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

● Wireless network settings ● DNS settings ● IPSec rules ● Configuring VPN settings ● Configuring HP Velocity Wired network settings The following table describes the options available in the Wired tab of the Network Manager. Option Enable IPv6 Ethernet Speed Connection Method MTU Security Settings Description Enables IPv6. IPv4 is used by default, and they cannot be used at the same time. Lets you set the Ethernet Speed. If your switch or hub does not have a special requirement, leave this at the default setting of Automatic. Lets you choose between Automatic and Static. If your network environment is using DHCP, then the Automatic option should work without any further configurations needed. If Static is selected, the Static Address Configuration settings will become available. Be sure to input these values according to whether you are using IPv4 or IPv6. Allows you to enter the maximum transmission unit (in bytes). Lets you set the authentication setting to one of the following: ● None ● 802.1X-TTLS ● 802.1X-PEAP ● 802.1X-TLS Note the following about TTLS and PEAP: ● The Inner Authentication option should be set to whatever your server supports. ● The CA Certificate setting should point to the server's certificate on the local client. ● The Username and Password are the user's credentials. Note the following about TLS: ● The CA Certificate setting should point to the server's certificate on the local client. ● If your Private Key file is .p12 or .pfx, then the User Certificate setting can be left blank. ● The Identity setting should be the username that corresponds to the user certificate. ● The Private Key Password setting is the password of the user's private key file. Wireless network settings The following table describes the options available in the Wireless tab of the Network Manager. NOTE: This tab is available only if the client has a wireless adapter. Option Scan AP Description Scans for available wireless networks. 16 Chapter 4 Control Panel configurations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
●
Wireless network settings
●
DNS settings
●
IPSec rules
●
Configuring VPN settings
●
Configuring HP Velocity
Wired network settings
The following table describes the options available in the
Wired
tab of the Network Manager.
Option
Description
Enable IPv6
Enables IPv6. IPv4 is used by default, and they cannot be used at the same time.
Ethernet Speed
Lets you set the Ethernet Speed. If your switch or hub does not have a special requirement,
leave this at the default setting of
Automatic
.
Connection Method
Lets you choose between
Automatic
and
Static
. If your network environment is using DHCP,
then the
Automatic
option should work without any further configurations needed.
If
Static
is selected, the
Static Address Configuration
settings will become available. Be sure
to input these values according to whether you are using IPv4 or IPv6.
MTU
Allows you to enter the maximum transmission unit (in bytes).
Security Settings
Lets you set the authentication setting to one of the following:
●
None
●
802.1X-TTLS
●
802.1X-PEAP
●
802.1X-TLS
Note the following about TTLS and PEAP:
●
The
Inner Authentication
option should be set to whatever your server supports.
●
The
CA Certificate
setting should point to the server’s certificate on the local client.
●
The
Username
and
Password
are the user’s credentials.
Note the following about TLS:
●
The
CA Certificate
setting should point to the server’s certificate on the local client.
●
If your
Private Key
file is .p12 or .pfx, then the
User Certificate
setting can be left blank.
●
The
Identity
setting should be the username that corresponds to the user certificate.
●
The
Private Key Password
setting is the password of the user’s private key file.
Wireless network settings
The following table describes the options available in the
Wireless
tab of the Network Manager.
NOTE:
This tab is available only if the client has a wireless adapter.
Option
Description
Scan AP
Scans for available wireless networks.
16
Chapter 4
Control Panel configurations