IBM 7945E2U User Manual - Page 147

Moving the SAS controller retention bracket

Get IBM 7945E2U PDF manuals and user guides View all IBM 7945E2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 147 highlights

Moving the SAS controller retention bracket Note: This procedure applies only to servers that have the following SAS riser-card. USB hypervisor connector PCI Express SAS controller connector SATA tape signal Tape drive power USB tape signal SAS controller error LED SAS riser card (tape-enabled model server) To move the SAS controller side retention bracket to a different position to accommodate the dimensions of the current SAS ServeRAID controller, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 37. 2. Make sure that the server and all peripheral devices are turned off and that the power cords and all external cables are disconnected. 3. Remove the SAS riser-card assembly from the server (see "Removing the SAS riser-card and controller assembly" on page 117). 4. Remove the ServeRAID controller from the SAS riser-card. Chapter 2. Installing optional devices 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Moving the SAS controller retention bracket
Note:
This procedure applies only to servers that have the following SAS
riser-card.
USB hypervisor
connector
USB
tape
signal
PCI Express SAS
controller connector
SATA tape signal
Tape drive
power
SAS controller
error LED
SAS riser card
(tape-enabled model server)
To move the SAS controller side retention bracket to a different position to
accommodate the dimensions of the current SAS ServeRAID controller, complete
the following steps:
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 37.
2.
Make sure that the server and all peripheral devices are turned off and that the
power cords and all external cables are disconnected.
3.
Remove the SAS riser-card assembly from the server (see “Removing the SAS
riser-card and controller assembly” on page 117).
4.
Remove the ServeRAID controller from the SAS riser-card.
Chapter 2. Installing optional devices
131