IBM 7945E2U User Manual - Page 82

in the controller. Press the riser card into place until the latch at the rear of, system board

Get IBM 7945E2U PDF manuals and user guides View all IBM 7945E2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

15. Install the SAS controller front retention bracket that you got from step 14: a. Align the retention bracket controller slot so that it faces the rear of the server. b. Place the bracket tabs in the holes on the chassis and slide the bracket to left until it clicks into place. 16. Remove the fillers (if they are installed) from the two connectors on the SAS controller that comes with the option kit. 17. Install the SAS controller: a. Insert the SAS controller into the connector on the SAS riser-card. b. Insert the front of the SAS controller into the front retention bracket. c. Install the SAS riser-card with the SAS controller into the connector on the system board, making sure that the alignment post goes through the hole in the controller. Press the riser card into place until the latch at the rear of the card snaps closed. 18. Connect the SAS signal cables to the SAS controller: a. Connect the SAS signal cable from the right side of the hard disk drive backplane to the right front connector on the SAS controller (as facing the front of the server). 66 System x3650 M3 Types 4255, 7945, and 7949: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
15.
Install the SAS controller front retention bracket that you got from step 14:
a.
Align the retention bracket controller slot so that it faces the rear of the
server.
b.
Place the bracket tabs in the holes on the chassis and slide the bracket to
left until it clicks into place.
16.
Remove the fillers (if they are installed) from the two connectors on the SAS
controller that comes with the option kit.
17.
Install the SAS controller:
a.
Insert the SAS controller into the connector on the SAS riser-card.
b.
Insert the front of the SAS controller into the front retention bracket.
c.
Install the SAS riser-card with the SAS controller into the connector on the
system board, making sure that the alignment post goes through the hole
in the controller. Press the riser card into place until the latch at the rear of
the card snaps closed.
18.
Connect the SAS signal cables to the SAS controller:
a.
Connect the SAS signal cable from the right side of the hard disk drive
backplane to the right front connector on the SAS controller (as facing the
front of the server).
66
System x3650 M3 Types 4255, 7945, and 7949: Installation and User’s Guide