IBM 7945E2U User Manual - Page 151

Installing the optional two-port Ethernet adapter, as shown in the following illustration.

Get IBM 7945E2U PDF manuals and user guides View all IBM 7945E2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 151 highlights

Installing the optional two-port Ethernet adapter To install an Ethernet adapter, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 37. 2. Make sure that the server is turned off, all external cables and power cords are disconnected, and the cover has been removed. For more information, see "Turning off the server" on page 22 and "Removing the cover" on page 44. 3. Attach the rubber stopper on the chassis, along the edge of the system board, as shown in the following illustration. Rubber stopper Rubber stopper Ethernet adapter connector 4. Remove the adapter filler panel on the rear of the chassis (if it has not been removed already). 5. Install the two standoffs on the system board. 6. Insert the bottom tabs of the metal clip into the port openings from outside the chassis. Chapter 2. Installing optional devices 135

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Installing the optional two-port Ethernet adapter
To install an Ethernet adapter, complete the following steps:
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 37.
2.
Make sure that the server is turned off, all external cables and power cords are
disconnected, and the cover has been removed. For more information, see
“Turning off the server” on page 22 and “Removing the cover” on page 44.
3.
Attach the rubber stopper on the chassis, along the edge of the system board,
as shown in the following illustration.
Rubber
stopper
Ethernet
adapter connector
Rubber
stopper
4.
Remove the adapter filler panel on the rear of the chassis (if it has not been
removed already).
5.
Install the two standoffs on the system board.
6.
Insert the bottom tabs of the metal clip into the port openings from outside the
chassis.
Chapter 2. Installing optional devices
135