IBM 7945E2U User Manual - Page 150

Removing a USB hypervisor memory key, SAS riser-card to unlock it from the connector.

Get IBM 7945E2U PDF manuals and user guides View all IBM 7945E2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

Removing a USB hypervisor memory key To remove the USB hypervisor memory key, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 37. 2. Turn off the server and peripheral devices and disconnect all power cords and external cables (see "Turning off the server" on page 22). 3. Remove the cover (see "Removing the cover" on page 44). 4. Locate the SAS riser-card assembly, which is near the left front corner of the server. 5. Push the blue locking collar on the USB hypervisor connector back toward the SAS riser-card to unlock it from the connector. 6. Pull the hypervisor memory key from the USB hypervisor connector. If you have other devices to install or remove, do so now. Otherwise, go to "Completing the installation" on page 139. Note: You must configure the server not to look for the hypervisor USB drive. See Chapter 3, "Configuring the server," on page 143 for information about disabling hypervisor support. 134 System x3650 M3 Types 4255, 7945, and 7949: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Removing a USB hypervisor memory key
To remove the USB hypervisor memory key, complete the following steps:
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 37.
2.
Turn off the server and peripheral devices and disconnect all power cords and
external cables (see “Turning off the server” on page 22).
3.
Remove the cover (see “Removing the cover” on page 44).
4.
Locate the SAS riser-card assembly, which is near the left front corner of the
server.
5.
Push the blue locking collar on the USB hypervisor connector back toward the
SAS riser-card to unlock it from the connector.
6.
Pull the hypervisor memory key from the USB hypervisor connector.
If you have other devices to install or remove, do so now. Otherwise, go to
“Completing the installation” on page 139.
Note:
You must configure the server not to look for the hypervisor USB drive. See
Chapter 3, “Configuring the server,” on page 143 for information about disabling
hypervisor support.
134
System x3650 M3 Types 4255, 7945, and 7949: Installation and User’s Guide