IC Realtime IPFX-D80V-IRW1 Product Manual - Page 79

Parameter, Description, A demonstration of configuring IP address with ARP/Ping., Reply

Get IC Realtime IPFX-D80V-IRW1 PDF manuals and user guides View all IC Realtime IPFX-D80V-IRW1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Parameter Description Defaut Gateway Preferred DNS Alternate DNS  IPv6 does not have subnet mask.  The default gateway must be in the same network segment with the IP address. IP address of the preferred DNS IP address of the alternate DNS Select the check box, get the device MAC address, and then you can modify and configure the device IP address with ARP/ping command. This is enabled by default. During reboot, you will have no more than 2 minutes to configure the device IP address by a ping packet with certain length, the server will be turned off in 2 minutes, or it will be turned off immediately after the IP address is successfully configured. If this is not enabled, the IP address cannot be configured with ping packet. A demonstration of configuring IP address with ARP/Ping. 1. Keep the camera that needs to be configured and the PC within the same local network, and then get a usable IP address. 2. Get the MAC address of the camera from device label. 3. Open command editor on the PC and enter the following command. Enable ARP/Ping to set IP address service 4. 5. 6. Click Save. Reboot camera. Check the PC command line, if information such as Reply from 192.168.0.125... is displayed, the configuration succeeds, and you can turn it off then. Enter http://(IP address) in the browser address bar to log in. Basic Configuration 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
Basic Configuration
71
Parameter
Description
Defaut Gateway
IPv6 does not have subnet mask.
The default gateway must be in the same network segment with
the IP address.
Preferred DNS
IP address of the preferred DNS
Alternate DNS
IP address of the alternate DNS
Enable
ARP/Ping
to set IP address
service
Select the check box, get the device MAC address, and then you can
modify and configure the device IP address with ARP/ping command.
This is enabled by default. During reboot, you will have no more than 2
minutes to configure the device IP address by a ping packet with
certain length, the server will be turned off in 2 minutes, or it will be
turned off immediately after the IP address is successfully configured. If
this is not enabled, the IP address cannot be configured with ping
packet.
A demonstration of configuring IP address with ARP/Ping.
1.
Keep the camera that needs to be configured and the PC within the
same local network, and then get a usable IP address.
2.
Get the MAC address of the camera from device label.
3.
Open command editor on the PC and enter the following command.
4.
Reboot camera.
5.
Check the PC command line, if information such as
Reply from
192.168.0.125…
is displayed, the configuration succeeds, and you
can turn it off then.
6.
Enter http://(IP address) in the browser address bar to log in.
Click
Save
.